KitchenAid Pro Line Series installation instructions Venting requirements, Venting methods

Page 5

Venting requirements

Vent system must terminate to the outside.

Do not terminate the vent system in an attic or other enclosed area.

Do not use 4 inch (10.2 cm) laundry-type wall caps.

Use 6 " (15.2 cm) metal vent only. Rigid metal vent is recommended. Do not use plastic or metal foil vent.

For the most efficient and quiet operation:

Use no more than three 90° elbows.

If an elbow is used, install it as far away from the hood’s vent motor exhaust opening as possible.

Make sure there is a minimum of 24" (61 cm) of straight vent between the elbows if more than one elbow is used.

Do Not install two elbows together.

The length of vent system and number of elbows should be kept to a minimum to provide efficient performance.

The vent system must have a damper. If roof or wall cap has a damper, Do Not use damper supplied with the range hood.

Use duct tape to seal all joints in the vent system.

Use caulking to seal exterior wall or roof opening around the cap.

Determine which venting method is best for your application and follow “Preparation” under ”Installation steps“ on Page 5.

Venting methods

This range hood is set for venting to the outside. For non-vented (recirculating) installation, a conversion kit is required. See "Non-vented (recirculating) installations" on page 2.

Vent system needed for installation is not included. Use 6" (15.2 cm) round vent.

Vent system can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.

The 6" (15.2 cm) round vent system length should not exceed 35 ft. (10.7 m).

Vertical roof venting

Horizontal wall venting

roof cap

wall cap

Calculating the vent system length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent piece

6" (15.2 cm) round

45° elbow

2.5 feet

 

(0.8 m)

90° elbow

5.0 feet

 

(1.5 m)

Example vent system

wall

cap

90° elbow

6 ft. (1.8 m)

2ft.

(0.6 m)

Maximum length

= 35 ft. (10.7 m)

1

— 90° elbow

=

5 ft.

(1.5 m)

8 ft. (2.4 m) straight

=

8 ft.

(2.4 m)

1

— wall cap

=

0 ft.

(0 m)

system length

= 13 ft.

(3.9 m)

Note: Flexible vent is Not recommended.

If it is used, each foot of flexible vent used is equivalent to two feet

(61 cm) of straight metal vent when calculating the vent system length. (Example: A flexible elbow equals two standard elbows.)

5

Image 5
Contents Quick Reference Installation Instructions Use and Care GuideBefore you Start Your safety and the safety of others is very importantParts supplied Tools needed Parts neededWall Anchors chimney mounting brackets Mounting screws Wall anchors Mounting screwsCabinet dimensions Product dimensionsVented installations Non-vented recirculating installationsVenting methods Venting requirementsPreparation Installation stepsElectrical requirements For vented installations, go to Step Check operation Blower indicatorAs shown LightThis hood uses two 12-volt, 20 watt halogen lamps Use and Care InformationOperation Accessories Wiring diagramCleaning Replacement Charcoal FilterKitchenAid will not PAY for WarrantyKitchenAid will PAY for Our consultants provide assistance with Requesting Assistance or Service807 area code in Ontario Direct service branchesExcept 807 area code Page Page Page Pièce n 437500563/8285349 Étapes de l’installationRéférence rapide Avant de Commencer Demander à un technicien qualifié d’installer cette hotteVotre sécurité et celle des autres est très importante « Alimentation électrique »Pièces nécessaires Outillage nécessaireSerre-câbles de 12,7 mm 1/2 po homologation U.L. ou C.S.A Chevilles d’ancrage Vis de montageDimensions des placards Dimensions du produitInstallation avec décharge à l’extérieur Installation sans décharge à l’extérieur recyclageNe pas raccorder deux coudes ensemble Calcul de la longueur effective du système de déchargeExemple de système de décharge Bouche de Décharge murale Coude à M 6 pi M 2 piContacter un électricien qualifié pour l’installation Étapes de l’installationAlimentation électrique PréparationPasser à l’étape Percer un trou de 3,2 cm 1 1/4 po à cet endroitRaccordement électrique 27. Réinstaller les filtresVeiller à ce que les Flèches de repérage Répéter ce processus pour les autres filtresDu ventilateur Renseignements d’utilisation et d’entretienAlimenter le circuit électrique Pattes de support Lampe Appuyer sur le bouton « 1 »Dépose des filtres Pour commander au Canada, téléphoner au AccessoiresSchéma de câblage Filtre à charbon de rechangeKitchenAid NE Paiera PAS GarantieKitchenAid Paiera Nos consultants fournissent de l’assistance pour Si vous avez besoin de pièces de rechangePour plus dassistance Succursales de service direct Si vous avez besoin dassistance ou de service au CanadaPour plus d’assistance ’exception de l’indicatif régional

Pro Line Series specifications

The KitchenAid Pro Line Series stands as a hallmark of culinary excellence, combining professional-grade performance with a sleek design that suits both aspiring home cooks and seasoned chefs. Known for their robust construction and powerful capabilities, these appliances are engineered to elevate the cooking experience.

One of the key features distinguishing the Pro Line Series is its powerful motor. With heavy-duty options capable of delivering high torque, these kitchen appliances adeptly handle a variety of tasks, from kneading dense bread dough to whipping cream into soft peaks. The Pro Line Series includes both stand mixers and blenders, each equipped with motors specifically designed to sustain heavy use without compromising on performance.

The stand mixers in this series come with a variety of bowl sizes, including the 7-quart capacity, allowing for large batches of ingredients. This feature is particularly beneficial for anyone preparing meals for gatherings or experimenting with complex recipes. Additionally, they offer multiple attachments ranging from dough hooks to food processors, making them versatile tools in any kitchen.

Furthermore, the KitchenAid Pro Line Series incorporates advanced mixing technologies such as the planetary mixing action, which ensures thorough mixing by rotating the beater while also spinning around the bowl’s interior. This efficient design minimizes the need for manual scraping and maximizes ingredient integration.

For the blenders in the Pro Line Series, they feature stainless steel blades and a unique design that fosters optimal blending efficiency. With multiple speed settings and a powerful motor, these blenders can handle everything from smoothies to soups. Some models even come equipped with pre-programmed settings that tailor the blending process to specific recipes, ensuring consistency every time.

Durability is another hallmark of the Pro Line Series. Crafted with high-quality materials, these appliances not only provide aesthetic appeal but are also built to withstand the rigors of daily use. A heavy-duty die-cast metal construction provides stability during mixing or blending, reducing vibrations and enhancing safety.

In conclusion, the KitchenAid Pro Line Series is a testament to exceptional design and engineering. With its powerful performance, advanced technology, and durable construction, it offers a professional-quality solution for home cooks keen on pushing culinary boundaries. Whether tackling simple recipes or intricate dishes, the Pro Line is a trusted partner in the kitchen, empowering users to create confidently and efficiently.