KitchenAid Pro Line Series installation instructions For vented installations, go to Step

Page 7

1/16"

vertical(1.6 mm)

centerline center notches

7. Place one of the chimney brackets against the wall so that its top edge is 1/16” (2.0 mm) from the ceiling or soffit and level.

Align the center notches of the bracket and the centerline.

Mark the centers of the bracket holes

16-13/16"

(41.1 mm)

8. Place the other chimney bracket on the wall so that it’s lower edge is 16-3/16” (41.1 cm) from the ceiling or soffit and level.

Align the center notches of the bracket and the centerline.

Mark the centers of the bracket holes.

9. If installing into wood, drill four 3/32” (2.4 mm) holes.

If installing into plaster or dry wall, drill four 3/16” (4.8 mm) holes. Insert wall anchors into each hole flush with the wall.

10. Attach each bracket to wall with two No. 8 Phillips head wood screws. Tighten screws securely.

11. If the hood is to be vented to the outside and the vent system has not been installed, install it now. The vent system must be installed before the hood. See “Venting methods” on Page 4.

12. Determine the location where the power supply cable will be run through the wall.

Note: For wiring flexibility, the wiring box is external to the hood motor. About 24” (61 cm) of wire connects the box to the hood motor.

Make sure the lower chimney cover will hide selected location.

Drill a 1-1/4” (3.2 cm) diameter hole at this location.

The wiring box mounting holes needed for your installation can be marked and drilled now or in Step 16.

Pull enough power supply cable through the wall to allow for easy connection to hood’s wiring box.

leveling screw

13. Use a flat-blade screwdriver and tighten the two leveling screws located close to the mounting brackets.

14. Use Phillips screwdriver and remove wiring box cover. Set cover aside, it will be reinstalled in Step 21.

For vented installations, go to Step 16.

For non-vented (recirculating) installations, go to Step 15.

15. Install non-vented (recirculating) conversion kit ordered for your hood.

diverter

vent motor

a. Fit the diverter over the vent motor exhaust outlet and push down to seat on outlet. Make sure diverter exhaust outlets are parallel with vent motor sides so that they will align with vent cover openings in lower chimney.

exhaust

diverter extension

b. Install the two vent extension pieces onto the diverter pushing them until they stop.

Go to Step 16.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

16. Lift the hood and place the hood mounting brackets over the mounting screws. Securely tighten the screws.

17. Level the hood. Adjust the two leveling screws (See Step 13) as needed.

18. If not previously done, center the wiring hole in the box over the hole in the wall and mark the two box mounting holes and drill holes as needed for your installation.

19. Install 1/2” (12.7 mm) strain relief in wiring box.

7

Image 7
Contents Quick Reference Installation Instructions Use and Care GuideBefore you Start Your safety and the safety of others is very importantWall anchors Mounting screws Tools needed Parts neededParts supplied Wall Anchors chimney mounting brackets Mounting screwsNon-vented recirculating installations Product dimensionsCabinet dimensions Vented installationsVenting methods Venting requirementsElectrical requirements Installation stepsPreparation For vented installations, go to Step Light Blower indicatorCheck operation As shownOperation Use and Care InformationThis hood uses two 12-volt, 20 watt halogen lamps Replacement Charcoal Filter Wiring diagramAccessories CleaningKitchenAid will PAY for WarrantyKitchenAid will not PAY for Our consultants provide assistance with Requesting Assistance or ServiceExcept 807 area code Direct service branches807 area code in Ontario Page Page Page Référence rapide Étapes de l’installationPièce n 437500563/8285349 « Alimentation électrique » Demander à un technicien qualifié d’installer cette hotteAvant de Commencer Votre sécurité et celle des autres est très importanteChevilles d’ancrage Vis de montage Outillage nécessairePièces nécessaires Serre-câbles de 12,7 mm 1/2 po homologation U.L. ou C.S.AInstallation sans décharge à l’extérieur recyclage Dimensions du produitDimensions des placards Installation avec décharge à l’extérieurBouche de Décharge murale Coude à M 6 pi M 2 pi Calcul de la longueur effective du système de déchargeNe pas raccorder deux coudes ensemble Exemple de système de déchargePréparation Étapes de l’installationContacter un électricien qualifié pour l’installation Alimentation électriquePasser à l’étape Percer un trou de 3,2 cm 1 1/4 po à cet endroitRépéter ce processus pour les autres filtres 27. Réinstaller les filtresRaccordement électrique Veiller à ce que les Flèches de repérageAlimenter le circuit électrique Renseignements d’utilisation et d’entretienDu ventilateur Dépose des filtres Appuyer sur le bouton « 1 »Pattes de support Lampe Filtre à charbon de rechange AccessoiresPour commander au Canada, téléphoner au Schéma de câblageKitchenAid Paiera GarantieKitchenAid NE Paiera PAS Pour plus dassistance Si vous avez besoin de pièces de rechangeNos consultants fournissent de l’assistance pour ’exception de l’indicatif régional Si vous avez besoin dassistance ou de service au CanadaSuccursales de service direct Pour plus d’assistance

Pro Line Series specifications

The KitchenAid Pro Line Series stands as a hallmark of culinary excellence, combining professional-grade performance with a sleek design that suits both aspiring home cooks and seasoned chefs. Known for their robust construction and powerful capabilities, these appliances are engineered to elevate the cooking experience.

One of the key features distinguishing the Pro Line Series is its powerful motor. With heavy-duty options capable of delivering high torque, these kitchen appliances adeptly handle a variety of tasks, from kneading dense bread dough to whipping cream into soft peaks. The Pro Line Series includes both stand mixers and blenders, each equipped with motors specifically designed to sustain heavy use without compromising on performance.

The stand mixers in this series come with a variety of bowl sizes, including the 7-quart capacity, allowing for large batches of ingredients. This feature is particularly beneficial for anyone preparing meals for gatherings or experimenting with complex recipes. Additionally, they offer multiple attachments ranging from dough hooks to food processors, making them versatile tools in any kitchen.

Furthermore, the KitchenAid Pro Line Series incorporates advanced mixing technologies such as the planetary mixing action, which ensures thorough mixing by rotating the beater while also spinning around the bowl’s interior. This efficient design minimizes the need for manual scraping and maximizes ingredient integration.

For the blenders in the Pro Line Series, they feature stainless steel blades and a unique design that fosters optimal blending efficiency. With multiple speed settings and a powerful motor, these blenders can handle everything from smoothies to soups. Some models even come equipped with pre-programmed settings that tailor the blending process to specific recipes, ensuring consistency every time.

Durability is another hallmark of the Pro Line Series. Crafted with high-quality materials, these appliances not only provide aesthetic appeal but are also built to withstand the rigors of daily use. A heavy-duty die-cast metal construction provides stability during mixing or blending, reducing vibrations and enhancing safety.

In conclusion, the KitchenAid Pro Line Series is a testament to exceptional design and engineering. With its powerful performance, advanced technology, and durable construction, it offers a professional-quality solution for home cooks keen on pushing culinary boundaries. Whether tackling simple recipes or intricate dishes, the Pro Line is a trusted partner in the kitchen, empowering users to create confidently and efficiently.