Denon AVP-A1HD, AVC-A1HD Before starting Auto Setup, Set up the subwoofer, Set up the microphone

Page 14

Before starting Auto Setup

1 Set up the subwoofer

If using a subwoofer capable of the following adjustments, set up the subwoofer as shown below.

nWhen using a subwoofer with a direct mode

Set the direct mode to “On” and disable the volume adjustment and crossover frequency setting.

nWhen using a subwoofer without a direct mode

Make the following settings:

Volume : “12 o’clock position”

Crossover frequency : “Maximum/Highest Frequency”

Low pass filter : “Off”

Standby mode : “Off”

2 Set up the microphone

Mount the setup microphone on a tripod or stand and place it in the main listening position.

When placing the setup microphone, adjust the height of the sound receptor to the level of the listener’s ear.

When starting Auto Setup, always use the supplied setup microphone (DM-A409).

Correct measurements cannot be taken if the setup microphone from the prior upgrade (DM-A505Z) is used.

Sound receptor

Setup microphone

If you do not have a tripod or stand, set up the microphone on, for example, a seat without a back.

NOTE

Do not hold the setup microphone in your hand during measurements.

Avoid placing the setup microphone close to a seat back or wall as sound reflections may give inaccurate results.

3 Connect the setup microphone Connect the setup microphone to the SETUP MIC jack of this unit.

When placing the setup microphone, adjust the height of the sound receptor to the level of the listener’s ear.

When the setup microphone is connected, the setup screen is displayed.

GSetup screen AVC-A1HDH

AUTO SETUP

STEP1 Preparation

1 2 3 4 5 6

Connect the speakers and place them according

to the recommendations in the manual.

 

Set the following items

 

if necessary.

 

Amp Assign

 

Channel Select

 

Auto Setup Start

 

Enter

RETURN Cancel

Start Auto Setup

 

GSetup screen AVP-A1HDH

AUTO SETUP

STEP1 Preparation

1 2 3 4 5 6

Connect the speakers and place them according

to the recommendations in the manual.

 

Set the following items

 

if necessary.

 

Pre-out Assign

 

XLR Out Polarity

 

Channel Select

 

Auto Setup Start

 

Enter

RETURN Cancel

Start Auto Setup

 

Getting Started Connections Setup Other Operations Multi-Zone Information Troubleshooting Specifications

13

Image 14
Contents Symbols used in this manual GOriginal versionHContents Getting Started Functions that are added/changed/deleted by this upgradeAccessories Additional functionsChanged Functions Deleted FunctionsRear Panel Changes to the Panel DisplayFront Panel GWith the door openHPart Names and Functions DisplayMain remote control unit RC-1067 Speaker InstallationRemote Control Unit ConnectionsSpeaker Connections Built-in amplifier Left R Right Subwoofer with built-in amplifierThis unit Subwoofer This unitTelevision setting that converts 2D video to 3D video off External Power AmplifierPower amplifier Over the playback videoGUI Menu Operations GUI Menu MapVpage 23 ~ 34, mpage 31, 34 ~ 38 InformationSource Select vmpage 44 ~ About the main listening position *M Auto SetupAbout setup microphone placement SBLWhen using a subwoofer with a direct mode Before starting Auto SetupSet up the subwoofer When using a subwoofer without a direct modePreparation Auto SetupAAuto Setup Return Configuring Various SettingsStart Auto Setup Detection & Measurement main Measuring the subwoofer volume levelWhen measuring has stopped EnterAdjusting the subwoofer volume level MainvpageMeasurement 2nd 8th CalculationProceed to Store vpage Check StoreSave the measurement results Auto Setup is complete FinishError messages Examples Error details MeasuresDParameter Check Direct ModeSOption OFFASpeaker Configuration Manual SetupSpeaker Setup FChannel Level SSubwoofer SetupDistance HTHX Audio Setup GCrossover FrequencyS2ch Direct/Stereo Audio SetupAEXT. in Setup DAuto Surround Mode FManual EQAmp Assign AVC-A1HD Option Setup AVC-A1HD Option Setup AVP-A1HDAssign Mode Extension ChannelPre-out Assign Power On Level DPOA Setting AVP-A1HDVolume Limit Link CheckWall Paper Master VolumeScreensaver FormatSetting with Respect to the Surround Mode Setting with Respect to the ZoneSetting with Respect to the Input Source Setting with Respect to the MonitorSelectable items ZONE4 Select Rec Select ⋅ RestorerA4Dimmer AVC-A1HD A6Dimmer AVP-A1HD Selectable items Bright Dim DarkUpgrade Status Check for UpdateUpgrade Add New FeatureSurround Playback of 2-channel Sources Surround ModeOperating from the main unit or main remote control unit Playing Multi-channel Sources Dolby Digital, DTS, etcWhen using a front wide speaker When using a surround back speakerWhen using a front height speaker Standard PlaybackStandard ASurround Parameters ParametersAudio DecoderCenter Gain DimensionDelay Time PanoramaSTone Dynamic EQ DAudyssey SettingsMultEQ XT Reference Level OffsetAudyssey DSX Dynamic VolumeFA-DSX Soundstage Stage WidthAbout the Restorer function RestorerHAudio Delay Stage HeightQuick Select InformationStatus AMAIN ZoneConvenient Functions Playback of Blu-ray Disc HD audio using Denon Link 4thOther Operations and Functions Multi-Zone Settings with the Amp Assign Function Amp Assign / Multi-Zone Connections and Operations AVC-A1HDF9.1-channel playback SettingPower amps to connect to the pre-out terminals Audio output speakersF9.1-channel playback FMulti-zone playback ON/OFF buttonSBR SBL Z3R Channel playback + ZONE3 stereo playbackPress ZONE3 ZONE3 OFF ZONE3 onFR FL SR SL SBR SBL ON/OFF orZONE3 ON/OFF ZONE2 on ZONE3 OFF ZONE2 OFF ZONE3 onFront Surr AMP Assign FH/FWZONE2 OFF ZONE3 on ZONE2 on ZONE3 OFF ZONE3 OFF S ZONE2 OFF ZONE3 on ZONE2 on ZONE3 OFFButton Bi-Wiring Switching with other modes not possibleAmp Assign mode Bi-Wiring SBL Z2R Amp Assign mode Bi & ZONE2Bi-Wiring Bi & ZONE2Amp Assign mode Bi & ZONE3 SBL Z3RZONE3 OFF ZONE2 OFF Amp Assign mode Bi & Zone MonoBi & Zone Mono ZONE3 on ZONE2 onAmp Assign mode Bi-Amp Speaker to connect Bi-AmpPress Standard Switching·················Surround Mode switchingAmp Assign mode 2CH Bi-Wiring Press Direct Stereo button Press Standard2ch Bi-Amp 2ch Bi-Amp Press DIRECT/ Stereo buttonR L R L Back Height Amp Assign mode Front HeightAmp Assign mode Front Wide Front Surr SURR.BACK AMP Assign FH/FW Free AssignAbout Denon Link 4th About Speaker InstallationOther Information GSpeaker abbreviationsHDTS Surround SurroundDolby Surround AudysseySurround Modes and Parameters Dolby HeadphoneWide Screen DSD Direct DSD Multi Direct Multi CH Direct StereoEXT. Multi CH DTS NeoxPCM DTS-HD PCM DTS-HD Dolby Dolby Digital Standard Multi CH Stereo or Direct 2ch Mode Relationship Between Amp Assign Setting and Speaker OutputMulti-Zone Power On/Off SettingSymptom Cause Countermeasure TroubleshootingGAudioH Symptom Cause Symptom Cause Countermeasure NAudio section SpecificationsNo specifications are changed by this upgrade Holdings Inc