Frymaster GSMS, GBC, GC Electrical Grounding Requirements, National Code Requirements

Page 9

installed so that products of combustion are removed efficiently, and that the kitchen ventilation sy- tem does not produce drafts that interfere with proper burner operation.

The cooker flue opening must not be placed close to the intake of the exhaust fan, and the cooker must never have its flue extended in a “chimney” fashion. An extended flue will change the combustion characteristics of the cooker, causing longer recovery time. It also frequently causes delayed ignition.

When installed beneath a ventilation hood, adequate distance must be maintained from the flue outlet of the cooker to the lower edge of the ventilation filter bank. Filters should be installed at an angle of 45° with a drip tray placed beneath the lowest edge of the filter. For U.S. installation, NFPA standard No. 96 states, “ A minimum distance of 18 inches (450mm) should be maintained between the flue outlet and the lower edge of the filter.”

For installations in other than the United States, installers should contact the appropriate local or national agency for information on the construction and installation of ventilating hoods.

ELECTRICAL GROUNDING REQUIREMENTS

All electrically operated appliances must be grounded in accordance with all applicable national and local codes, and where applicable, CE codes. A wiring diagram is located on the inside of the cooker door. Refer to the rating plate on the inside of the cooker door for the proper voltages.

DANGER

If this appliance is equipped with three-prong (grounding) plug, it must be plugged directly into properly grounded receptacle. Do not cut or remove the grounding prong from the plug.

DANGER

This equipment requires electrical power for operation.

Place the gas control valve in the OFF position in case of a prolonged power outage.

Do not attempt to use the equipment during a power outage.

NATIONAL CODE REQUIREMENTS

GSMS/GBC/GC cookers are manufactured to use the type of gas specified on the rating plate. The rating plate is attached to the inside of the cooker door. Connect a cooker only to the type of gas indicated on the rating plate.

Installation shall be made with a gas connector that complies with the national and local codes or regulations in force in the country in which the appliance is being installed. Quick-disconnect devices, if used, shall likewise comply with the national and local codes or regulations in force in the country in which the appliance is being installed

When installing GSMS/GBS/GC cookers in theUNITED STATES, the installation must conform to the latest edition of the Nation Fuel Gas Code, ANSI Z223.1. In addition, installation must comply

2-2

Page 8 Page 10
Image 9
Page 8 Page 10
Contents `8195311~ Hour Service HotlineFCC ComputersGAS Cookers GSMS, GBC and GC Table of Contents GAS Cookers GSMS, GBC, and GC General Information Parts Ordering and Service InformationRetain and Store this Manual in a Safe Place for Future USE Applicability and ValidityEquipment Description Safety InformationDefinitions Installation, Operating, and Service PersonnelWhat to do if your equipment arrives damaged Shipping Damage Claim ProcedureGAS Cookers GSMS, GBC, and GC Installation Instructions General Installation RequirementsClearance and Ventilation National Code Requirements Electrical Grounding RequirementsFCC Compliance Caster or Leg InstallationPage References for CE Standard are Tables 6 and A.2 of EN Countries Categories GAS Connection to the Gas LineMinimum incoming pipe size should be 1½38 mm Gas Connection Pipe SizesCE Standard for Burner Gas Pressure Non-CE Gas Conversion ComponentsNon-CE Gas Conversion Instructions CE Gas Conversion InstructionsIntroduction GAS Cookers GSMS, GBC, and GC Operating InstructionsOperating Instructions Fahrenheit or Celsius Temperature DisplayNormal Operation Shutting the Cooker Down Boiling Out the CookpotDaily Preventive Maintenance GAS Cookers GSMS, GBC, and GC Preventive MaintenanceCleaning and Adjusting the Combustion Air Blower Cleaning the Gas Valve Vent TubeBlower Housing Blower Wheel Pressure Tap Plug Typical Non-CE Valve Assembly Typical CE Measuring Flame Current Controller Simmer Mode AdjustmentManual Adjustment Before calling a servicer or the Frymaster Hotline GAS Cookers GSMS, GBC, and GC Operator TroubleshootingBurners do not Full Problem Probable Causes Corrective ActionWater Wiring Diagram Replacing the Controller This page Intentionally Left Blank Service Hotline

GC, GBC, GSMS specifications

The Frymaster GSMS, GBC, and GC series are advanced fryers designed to meet the demands of busy commercial kitchens. Renowned for their efficiency, reliability, and technology, these fryers are integral to restaurants, snack bars, and food service operations looking to elevate their frying capabilities.

One of the standout features of the Frymaster GSMS series is its ability to deliver consistent results with minimal effort. Equipped with smart technology, these fryers automatically adjust cooking times and temperatures to ensure food is cooked perfectly every time. This not only enhances food quality but also reduces the chances of operational errors, making it ideal for operators of all skill levels.

The GBC series is designed for versatility, featuring multiple fry pots. This allows different foods to be cooked simultaneously without the risk of cross-contamination. Whether you’re frying chicken, French fries, or doughnuts, the GBC series accommodates a wide variety of menus, helping restaurants maximize their offerings. Additionally, the models are energy efficient, significantly lowering operational costs associated with energy consumption.

The GC series represents the pinnacle of frying technology, integrating innovations that streamline cooking processes. One such innovation is the built-in filtration system that cleans oil during operation, extending its life and ensuring high-quality frying. This system not only enhances food flavor but also minimizes the need for frequent oil changes, significantly reducing waste and operational costs.

Another key characteristic across these Frymaster lines is their user-friendly control panels. These intuitive controls allow quick access to cooking settings and oil management, making the user experience seamless. Operators can easily monitor and adjust frying operations, which helps maintain peak performance and efficiency across a busy kitchen.

Moreover, safety features are paramount in these fryer models. Enhanced safety measures including automatic shut-off systems, temperature limit controls, and built-in alarms provide operators peace of mind in a fast-paced environment.

In summary, the Frymaster GSMS, GBC, and GC series fryers exemplify modern frying technology with their automation, versatility, and energy efficiency. These fryers not only support high-volume cooking but also prioritize safety and consistency, making them essential tools for any food service operation aiming for excellence.
Top Page Image Contents