Frymaster GAS Cookers GSMS, GBC, and GC Installation Instructions, Clearance and Ventilation

Page 8

GAS COOKERS GSMS, GBC, AND GC

INSTALLATION AND OPERATION MANUAL

CHAPTER 2: INSTALLATION INSTRUCTIONS

2.1General Installation Requirements

Qualified, licensed, and/or authorized installation or service personnel, as defined in Section 1.7 of this manual, should perform all installation and service on Frymaster equipment.

Conversion of this appliance from one type of gas to another should only be performed by qualified, licensed, and/or authorized installation or service personnel as defined in Section 1.7 of this manual.

Failure to use qualified, licensed, and/or authorized installation or service personnel (as defined in Section 1.7 of this manual) to install, convert to another gas type or otherwise service this equipment will void the Frymaster warranty and may result in damage to the equipment or injury to personnel.

Where conflicts exist between instructions and information in this manual and local or national codes or regulations, installation and operation shall comply with the codes or regulations in force in the country in which the equipment is installed.

Upon arrival, inspect the cooker carefully for visible or concealed damage. (SeeShipping Damage Claim Procedure in Chapter 1.)

CLEARANCE AND VENTILATION

The cooker(s) must be installed with 6 inches (150mm) clearance at both sides and back when installed adjacent to combustible construction; no construction; no clearance is required when installed adjacent to noncombustible construction. A minimum of 24 inches (600mm) clearance should be provided at the front of the cooker. To provide the airflow necessary for good combustion and burner operation, the areas surrounding the cooker front, sides, and rear must be kept clear and unobstructed.

DANGER

This appliance must be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances harmful to the health of personnel in the room in which it is installed.

CE Standard

Required airflow for the combustion air supply is 2m3/h per kW.

One of the most important considerations of efficient cooker operation is ventilation. Cookers must be installed in an area with an adequate air supply and adequate ventilation. Make sure the cooker is

2-1

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Hour Service Hotline `8195311~Computers FCCGAS Cookers GSMS, GBC and GC Table of Contents Parts Ordering and Service Information GAS Cookers GSMS, GBC, and GC General InformationRetain and Store this Manual in a Safe Place for Future USE Applicability and ValiditySafety Information Equipment DescriptionInstallation, Operating, and Service Personnel DefinitionsShipping Damage Claim Procedure What to do if your equipment arrives damagedClearance and Ventilation GAS Cookers GSMS, GBC, and GC Installation InstructionsGeneral Installation Requirements Electrical Grounding Requirements National Code RequirementsCaster or Leg Installation FCC CompliancePage References for CE Standard are Tables 6 and A.2 of EN Connection to the Gas Line Countries Categories GASGas Connection Pipe Sizes Minimum incoming pipe size should be 1½38 mmNon-CE Gas Conversion Components CE Standard for Burner Gas PressureCE Gas Conversion Instructions Non-CE Gas Conversion InstructionsGAS Cookers GSMS, GBC, and GC Operating Instructions IntroductionFahrenheit or Celsius Temperature Display Operating InstructionsNormal Operation Boiling Out the Cookpot Shutting the Cooker DownGAS Cookers GSMS, GBC, and GC Preventive Maintenance Daily Preventive MaintenanceCleaning the Gas Valve Vent Tube Cleaning and Adjusting the Combustion Air BlowerBlower Housing Blower Wheel Pressure Tap Plug Typical Non-CE Valve Assembly Typical CE Controller Simmer Mode Adjustment Measuring Flame CurrentManual Adjustment GAS Cookers GSMS, GBC, and GC Operator Troubleshooting Before calling a servicer or the Frymaster HotlineBurners do not Problem Probable Causes Corrective Action FullWater Wiring Diagram Replacing the Controller This page Intentionally Left Blank Service Hotline

GC, GBC, GSMS specifications

The Frymaster GSMS, GBC, and GC series are advanced fryers designed to meet the demands of busy commercial kitchens. Renowned for their efficiency, reliability, and technology, these fryers are integral to restaurants, snack bars, and food service operations looking to elevate their frying capabilities.

One of the standout features of the Frymaster GSMS series is its ability to deliver consistent results with minimal effort. Equipped with smart technology, these fryers automatically adjust cooking times and temperatures to ensure food is cooked perfectly every time. This not only enhances food quality but also reduces the chances of operational errors, making it ideal for operators of all skill levels.

The GBC series is designed for versatility, featuring multiple fry pots. This allows different foods to be cooked simultaneously without the risk of cross-contamination. Whether you’re frying chicken, French fries, or doughnuts, the GBC series accommodates a wide variety of menus, helping restaurants maximize their offerings. Additionally, the models are energy efficient, significantly lowering operational costs associated with energy consumption.

The GC series represents the pinnacle of frying technology, integrating innovations that streamline cooking processes. One such innovation is the built-in filtration system that cleans oil during operation, extending its life and ensuring high-quality frying. This system not only enhances food flavor but also minimizes the need for frequent oil changes, significantly reducing waste and operational costs.

Another key characteristic across these Frymaster lines is their user-friendly control panels. These intuitive controls allow quick access to cooking settings and oil management, making the user experience seamless. Operators can easily monitor and adjust frying operations, which helps maintain peak performance and efficiency across a busy kitchen.

Moreover, safety features are paramount in these fryer models. Enhanced safety measures including automatic shut-off systems, temperature limit controls, and built-in alarms provide operators peace of mind in a fast-paced environment.

In summary, the Frymaster GSMS, GBC, and GC series fryers exemplify modern frying technology with their automation, versatility, and energy efficiency. These fryers not only support high-volume cooking but also prioritize safety and consistency, making them essential tools for any food service operation aiming for excellence.
Top Page Image Contents