Frymaster Super Runner Series Accessing Fryers for Servicing, Cleaning the Gas Valve Vent Tube

Page 8

1.2 Accessing Fryers for Servicing

DANGER

Moving a fryer filled with cooking oil may cause spilling or splattering of the hot

liquid.

1.Drain all cooking oil from the fryer.

2.Shut off the gas supply to the unit and disconnect the unit from the gas supply.

3.Remove any attached restraining devices.

DANGER

Fryers must be at room temperature, empty of oil, and if fitted with legs, lifted during

movement to avoid damage and possible bodily injury.

DANGER

Hot shortening can cause severe burns. Avoid contact. Under all circumstances, oil must be removed from the fryer before attempting to move it to avoid oil spills, and the falls and severe burns that could occur. This fryer may tip and cause personal injury if not secured in a stationary position.

4.Relocate the fryer for service accessibility. If fryer is equipped with legs, lift the fryer to relocate it. Damage to the leg or leg support channel can result if the fryer is not lifted when moving.

5.After servicing is complete, reconnect the unit to the gas supply and reattach the restraining devices.

6.Refill the frypot with cooking oil.

1.3 Cleaning the Gas Valve Vent Tube

1.Set the fryer power switch and the gas valve to the "OFF" position.

2.Carefully unscrew the vent tube from the gas valve. NOTE: The vent tube may be straightened for ease in removal.

3.Pass a piece of ordinary binding wire through the tube to remove any obstruction. Remove the wire and blow through the tube to ensure it is clear.

4.Reinstall tube and bend so that the opening is pointing downward.

1-3

Image 8

Contents MAY Hour Service HotlineSuper Runner and Super Marathon Series Page Iii Table of Contents Parts List CE only Altitudes of 2000 feet or less Functional DescriptionNON-CE Altitudes of 2000 feet or less Pilot Ignition System ThermostatsAccessing Fryers for Servicing Cleaning the Gas Valve Vent TubeCalibrating the Operating Thermostat Check Burner Manifold Pressure Replacing the Operating Thermostat Adjusting the Pilot FlameReplacing Fryer Components Replacing the Operating Thermostat Replacing the High-Limit Thermostat Replacing the FrypotTroubleshooting and Problem Isolation Pilot FailuresAutomatic Pilot Dropout Check Complete System CheckSystem Resistance Check Pilot Fails to Light Improper Burner Functioning Filtration Problems Leaking Wiring Diagrams Current Production Units with Honeywell Gas Valve Non-CECurrent Production Units with Honeywell Gas Valve CE Current Production Units with Robertshaw Gas Valve After May UFF Filtration Wiring Diagram OptionalCabinetry Components, Single Fryers Channel, Base- Front & Rear Non-Filtration Single FryersSide Panel, Right Suff Base Components- SM Series With Suff FiltrationSide Panel, Left Door Assembly Components Panel, Outer Door- SM20G Assembly 106-2482SPAdditional Single Fryer Base Channel Components Cabinetry Components, Multi-Battery Frying SystemsBase Channel, Front & Rear- SM220G, SM50G See .1 For Accessories Fluecap, SM20/20/50GDean Millivolt GAS Fryers Parts List Thermostat, Sunne Use 807-1692 for CE Frypot and Burner System Components 1 SM220 and SM20/20/~ SystemsFlue Assembly- SM20G SR Series, SM35G, SM40G and SM50G Systems Burner, Right- SR38G, SR42G, SM35G, SM40G Burner, Center- SR38G, SR42G, SM35G, SM40GBurner, Left- SR38G, SR42G, SM35G, SM40G Shield, Burner Heat- SR52G, SM5025 106-1742SPFlue Assembly- SR52G, SM50G Flue Assembly- SR38G106-0696SPFlue Assembly- SR42G 106-0954SPFlue Assembly- SM35G, SM40G3 SR62, SM60G and SM80G Systems SM80G ShownFrypot- S/S- SM60G, SR62G Use 823-3511SP for SM160G Valve, Trailing Pilot- SM60G, SM80G, SR62G adjustment valveFrypot- M/S- SM80G Prior To 10/99 obsolete use Flue Assembly- SM80G Flue Assembly- SM60G, SR62GOil Drain Manifold Componets Oil Drain Manifold, Drain Flush and Drain Valve Components Drain Valve ComponentsPlace Over 2 3 Oil Drain Manifold, Drain Flush & Drain Valve Components Flush Oil Drain LineOil Return Manifold Components Oil Return Manifold Components Fryers with 1½ Drains810-0051 200-1143 809-0877 106-2568SP Not Illustrated Oil Return Manifold Components Fryers with 3 Drains Oil Return and Oil Flush Components Oil Return and Oil Flush Components Fryers with 1½ DrainsMicroswitch Bracket Assembly, Oil Return Oil Suction Start FittingOil Return and Oil Flush Components Fryers with 3 Drains Oil Suction Assembly Suction Manifold AssemblyUnder Fryer Filter UFF Components 1 SM50 and SM60 Series Fryers Except Ihop2 SM50 Series Fryers, Ihop UFF 50 with Filter Leaf 3 SM80 Series Fryers Single Under Fryer Filter Suff Components 1 SM50 Series Fryers2 SM60 and SM80 Series Fryers This page Intentionally Left Blank Service Hotline