Frymaster OCF30 operation manual Built-In Filtration System

Page 27

•Verify that the temperature and high-limit probes are properly connected, tightened and functioning properly, and that mounting hardware and probe guards are present and properly installed.

•Verify that component box and contactor box components (i.e. controller/controller, relays, interface boards, transformers, contactors, etc.) are in good condition and free from oil and other debris.

•Verify that component box and contactor box wiring connections are tight and that wiring is in good condition.

•Verify that all safety features (i.e. contactor shields, drain safety switches, reset switches, etc.) are present and functioning properly.

•Verify that the frypot is in good condition and free of leaks and that the frypot insulation is in serviceable condition.

•Verify that all wiring harnesses and connections are tight and in good condition.

5.5.2 Built-In Filtration System

•Inspect all oil-return and drain lines for leaks and verify that all connections are tight.

•Inspect the filter pan for leaks and cleanliness. If there is a large accumulation of crumbs in the crumb basket, advise the owner/operator that the crumb basket should be emptied into a fireproof container and cleaned daily.

•Verify that all O-rings and seals (including those on the quick-disconnect fittings) are present and in good condition. Replace O-rings and seals if worn or damaged.

•Check filtration system integrity as follows:

−Verify that filter pan cover is present and properly installed.

−With the filter pan empty, place each filter handle, one at a time, in the ON position. Verify that the pump activates and that bubbles appear in the oil of the associated frypot.

−Close all oil return valves (i.e., place all filter handles in the OFF position). Verify proper functioning of each oil return valve by activating the filter pump using the lever on one of the oil return handle microswitches. No air bubbles should be visible in any frypot.

−Verify that the filter pan is properly prepared for filtering, then drain a frypot of oil heated to 350°F (177°C) into the filter pan and close the frypot drain valve. Place the filter handle in the ON position. Allow all oil to return to the frypot, indicated by bubbles in the oil. Return the filter handle to the OFF position. The frypot should have refilled in no more than 2 minutes and 30 seconds.

5–4

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Oil Conserving Fryer OCF30 Electric Series Fryers Hour Service HotlineCanada Page Table of Contents Table of Contents Operator Troubleshooting Computer Information European Community CE Specific InformationDefinitions Service Information Shipping Damage Claim ProcedureGeneral Installation Requirements OCF30 II Series Electric Fryers Installation InstructionsClearance and Ventilation Australian Requirements Power RequirementsPage Finding Your WAY around the OCF30 Series Electric Fryer OCF30 Series Electric Fryer Operating InstructionsSetup Equipment Setup and Shutdown ProceduresInstall the Oil Reservoir Optional Oil Attendant Automatic Top-OffPrepare the System for Use Routine Oil Changes OCF30 Series Electric Fryers Filtration Instructions Preparation for Use with the Magnasol Filter Assembly Filtration Filter Pump Reset Switch Cleaning Draining and Disposing of Waste Oil ReassemblyPage OCF30 Series Electric Fryers Preventative Maintenance Inspect Fryer and Accessories for Damage- DailyClean Inside and Outside of the Fryer Cabinet Daily Page Check the Controller Set Point Accuracy Annual/Periodic System InspectionFryer Built-In Filtration System Introduction OCF30 Series Electric Fryers Operator TroubleshootingError Messages and Display Problems Troubleshooting Controller and Heating ProblemsOr LOw temp Basket Lift ProblemsAuto Top-Off Problems Filtration ProblemsExplanation Error Log Codes For 3000 Controller OnlyPage OCF30 Series Simplified Wiring with 3000 Controller OCF30 Series Electric Fryers Wiring DiagramsComponent Wiring with 3000 controller Domestic Component Wiring with CM3.5 controller Domestic Component Wiring with CM3.5 Controller CE Component Wiring with CM3.5 Controller CSA Contactor Box Delta Configuration Contactor Box WYE Configuration Assembled melter is shown in position Appendix B Solid Shortening Melter Use OCF30 Series Electric FryerBulk Oil Systems OCF30 Series Electric Fryer Appendix C Bulk OIL InstructionsDo not add HOT or Used oil to a JIB Filling the JIBDispose of Waste Oil Fill Vat from Bulk Tank Service Hotline
Related manuals
Manual 46 pages 8.96 Kb

OCF30 specifications

The Frymaster OCF30 is a state-of-the-art commercial fryer designed for efficiency, reliability, and versatility in high-demand kitchen environments. As part of the Frymaster family, this model is known for its innovative features that cater to various cooking needs, making it a popular choice among restaurant operators and culinary professionals.

One of the standout features of the OCF30 is its advanced oil filtration system. This feature enables operators to maintain oil quality for longer periods, resulting in better-tasting food and reduced oil consumption. The integrated filtration system can be operated on-demand or set to automatically filter oil at specific intervals, ensuring that the oil remains clean and enhancing food flavor consistently.

The OCF30 fryer also employs innovative heating technology, offering rapid temperature recovery. This allows for quicker cooking times and maximizes productivity during peak hours. With the ability to reach high temperatures swiftly, chefs can efficiently manage multiple orders without compromising on food quality.

Energy efficiency is another hallmark of the Frymaster OCF30. It is designed to minimize energy consumption while still delivering powerful cooking performance. This not only helps in reducing operational costs but also contributes to a more environmentally sustainable kitchen practice.

User-friendly controls and a digital display are integral to the OCF30's design, allowing for precise temperature management and easy monitoring of cooking times. Features such as programmable cooking settings enable chefs to replicate the cooking process with accuracy, ensuring consistency in food preparation.

The design of the OCF30 includes safety features that protect both the operator and the equipment. The fryer is equipped with built-in safeguards against overheating, and its construction includes durable materials that can withstand the rigors of a commercial kitchen.

In summary, the Frymaster OCF30 is a top-tier choice for commercial frying operations. With its advanced oil filtration system, rapid temperature recovery, energy efficiency, user-friendly controls, and safety features, it is engineered to enhance productivity and maintain food quality, making it an invaluable asset for any busy kitchen.
Top Page Image Contents