Frymaster H14 Series service manual Shipping Damage Claim Procedure, Service Information

Page 7

1.5Shipping Damage Claim Procedure

What to do if your equipment arrives damaged:

Please note that this equipment was carefully inspected and packed by skilled personnel before leaving the factory. The freight company assumes full responsibility for safe delivery upon acceptance of the equipment.

1.File Claim for Damages Immediately—Regardless of extent of damage.

2.Visible Loss or Damage—Be sure this is noted on the freight bill or express receipt and is signed by the person making the delivery.

3.Concealed Loss or Damage—If damage is unnoticed until equipment is unpacked, notify Freight Company or carrier immediately and file a concealed damage claim. This should be done within 15 days of date of delivery. Be sure to retain container for inspection.

1.6Service Information

McDonald’s store personnel perform routine maintenance. For non-routine maintenance or repairs, or for service information, contact your local Frymaster Authorized Service Center (FASC). Service information may also be obtained by calling the Frymaster Technical Services Department (1-800- 24FRYER). The following information will be needed in order to assist you efficiently:

Model Number _________________________

Serial Number _________________________

Voltage _______________________________

Nature of the Problem ___________________

_____________________________________

_____________________________________

RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE.

1-3

Image 7

Contents Frymaster H14 Series Electric Fryer Computers FCC Warranty Statement Parts Return Introduction Safety InformationGeneral European Community CE Specific Information Computer InformationService Information Shipping Damage Claim ProcedureDo not block the area around the base or under the fryers Installation InstructionsAfter Fryers Are Under The Fry Station Hood Power RequirementsFrypot Boil-Out Shutdown Equipment Setup and Shutdown ProceduresOperating Fryers With M100B Cooking Computers Introduction To The M-100B Cooking ComputerDescription Operating the Computer on Full-Vat Fryers M-100B Computer Operating InstructionsOperating the Computer on Split-Vat Fryers Open Drain Valve Indication M-100B Computer Problem Condition IndicatorsRecovery Out of Range REC LOC How to Enter the Setup Mode 1 M-100B Computer Setup ModeM-100B Computer Set-Up and Programming Instructions How to Configure the Computer for Use on an Electric Fryer How to Change the Computer’s Display LanguageHow to Change Computer Product/Temperature Displays How to Activate or Deactivate the Frypot BOIL-OUT Feature How to Enter the Program Mode 2 M-100B Computer Programming ModeHow to Reset the Computer to the Factory Defaults How to Enter a Product Name in a Test Menu How to Change the Cooking Temperature SetpointPage How to Suppress a Shake, QA, or Duty Function How to Display the Product Cycle Accumulator Information How to Display Use Time InformationHow to Use the Filter Countdown Timer Introduction to the Analog Controller Operating Fryers With Analog ControllersI J K L M N Analog Controller High-Limit Check Analog Controller Operating InstructionsPage Description Function Operating the BUILT-IN Filtration SystemSTEP-BY-STEP Filtration Instructions Page Page Page Page Page Page Page Care and Cleaning of Your Fryer and Filter System Water in the Filter PAN MSDU50 Preventive Maintenance Troubleshooting Preventive Maintenance and TroubleshootingComputer Panel Open Interface Board Visible Computer Panel Open Interface Board Visible Fryer Heating OilFrom Preceeding From Preceeding Is the AL LED illuminated? Controller Panel Open Interface Board Visible From Preceeding From Preceeding Filter System Operation Pump Motor ActuationReplace Controller Service ProceduresReplace Interface Board Replace Transformer Replace Temperature ProbeReplace Temperature Probe Replace Heating Element Replace Heating Element Remove the element mounting screws Left element- 9-pin Right element- 6-pin Connector Replace HIGH-LIMIT Replace Frypot Replace Contactor Contactor mounting screws Filtration Problem Resolution BUILT-IN Filter System Service ProceduresBUILT-IN Filter System Service Procedures FootPrint III Wiring Diagram Diagnostic LED Legend Electric Interface Board Diagnostic ChartCommon Electric McDONALDS H14 SERIES- FULL-VAT Wiring DiagramsSimplified GND Common Electric McDONALDS H14 SERIES- DUAL-VATCommon Electric McDONALDS H14 SERIES- FULL-VAT- Export WYE Common Electric McDONALDS H14 SERIES- DUAL-VAT- Export WYE McDonald’s Domestic Wiring DIAGRAMS, MainMcDonald’s European Community CE McDonald’s European Community CE Prior To 9/98 McDonald’s European Community CE XBIH14 McDonald’s Domestic Contactor McDonald’s European Community CE WYE Contactor McDonald’s European Community CE XBIH14 Contactor McDonald’s 440/480V Contactor McDonald’s Delta CSA Contactor McDonald’s Domestic Control Cord McDonald’s English Control Cord Footprint III, Early Configuration Wiring DIAGRAMS, Filter UnitsFootprint III, Late Configuration Accessories H14 Series Electric Fryers Parts ListPage Side , Cabinet 2 MH/BIH214, 314, 414, 514 Cabinet Assemblies Component Casters, Legs and Associated Hardware Component Box Assemblies/Associated Component Parts Page Control Panel Assembly Door Assembly Components Controller Assemblies Drain System Components Page McDonald’s Domestic, Dual-vat Elements and Related Components Component Hood Relay Box, Power Cords and Hood Cords Filter Base/Pan Assemblies 8.9.1 Filter Base Assemblies Filter Base Assembly, FootPrint Filter Pan Assemblies Filter Pan Assembly, Single FootPrint Filter Pump and Motor Assemblies Pump and Motor Assembly, 250V 50/60 Hz Page Flex Line Assembly, With Male/Female Ends Oil Return Linkage Assemblies and Components Frypot Assemblies and Drain Valve Components Thermostats and Related Components