Frymaster H14 Series service manual Operating the Computer on Split-Vat Fryers

Page 14

Operating the Computer on Split-Vat Fryers

1.Turn ON the cooking computer by pressing the ON/OFF switches . Pressing the left switch turns on the left side of the computer; pressing the right switch turns on the right side. A product name (for example, FR FRIES) will appear in the LED display corresponding to the switch pressed.

2.If the frypot temperature is below 180°F (82°C), the computer will automatically enter a warm-up cycle (often called a melt cycle). The heating elements will cycle on and off repeatedly, allowing the vegetable oil to heat gradually, without scorching. During the warm-up cycle, the heating mode indicator will alternately illuminate and go out as the elements cycle on and off. Within 45 minutes, the computer will exit the warm-up cycle and the heat mode indicator will remain continuously illuminated.

3.Select the product to be cooked by pressing the left or right product selection switches , depending upon the vat in which you wish to cook.

4.Once the frypot temperature is above 180°F (82°C), but still 15°F (8°C) or more below the setpoint temperature for the product displayed (for example, french fries), the computer will alternately display LOW TEMP and FR FRIES, and the heating mode indicator will remain continuously illuminated.

5.The cooking cycle cannot be started until the cooking oil is within ±15°F (8°C) of the programmed setpoint. When the frypot temperature is within ±15°F (8°C) of the programmed setpoint, the product name will be displayed continuously, indicating that the fryer is ready to cook the displayed product.

Viewing the Frypot Temperature (Actual or Setpoint)

To display the actual frypot temperature, press the temperature check switch once. To display the setpoint temperature, press the switch twice.

Cooking Product (Full-Vat or Split-Vat)

1.Fill basket(s) with product, lower the basket into the vegetable oil, then press the cook switch ( 1 or 2 ) that corresponds to the full- or split-vat to be used. This will activate the cooking cycle of the product.

Example 1: In a full-vat fryer, press cook switch 1 when the first basket of twin baskets of fries is dropped. Halfway through the first cooking cycle, drop the second basket and press cook switch 2 .

Example 2: The M-100B is programmed to cook Crispy Chicken (CSPY) and Chicken McNuggets (NUG) in the same side of a split-vat arrangement. Cook switch 1 corresponds to Crispy Chicken, and cook switch 2 corresponds to Chicken McNuggets.

2.The display will show the number of minutes and seconds of cooking time remaining.

3–4

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Frymaster H14 Series Electric Fryer Computers FCC Warranty Statement Parts Return General Safety InformationIntroduction Computer Information European Community CE Specific InformationShipping Damage Claim Procedure Service InformationInstallation Instructions Do not block the area around the base or under the fryersPower Requirements After Fryers Are Under The Fry Station HoodFrypot Boil-Out Introduction To The M-100B Cooking Computer Equipment Setup and Shutdown ProceduresOperating Fryers With M100B Cooking Computers ShutdownDescription M-100B Computer Operating Instructions Operating the Computer on Full-Vat FryersOperating the Computer on Split-Vat Fryers M-100B Computer Problem Condition Indicators Open Drain Valve IndicationRecovery Out of Range REC LOC M-100B Computer Set-Up and Programming Instructions 1 M-100B Computer Setup ModeHow to Enter the Setup Mode How to Change Computer Product/Temperature Displays How to Change the Computer’s Display LanguageHow to Configure the Computer for Use on an Electric Fryer How to Activate or Deactivate the Frypot BOIL-OUT Feature How to Reset the Computer to the Factory Defaults 2 M-100B Computer Programming ModeHow to Enter the Program Mode How to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test MenuPage How to Suppress a Shake, QA, or Duty Function How to Use the Filter Countdown Timer How to Display Use Time InformationHow to Display the Product Cycle Accumulator Information Operating Fryers With Analog Controllers Introduction to the Analog ControllerI J K L M N Analog Controller Operating Instructions Analog Controller High-Limit CheckPage Operating the BUILT-IN Filtration System Description FunctionSTEP-BY-STEP Filtration Instructions Page Page Page Page Page Page Page Care and Cleaning of Your Fryer and Filter System Water in the Filter PAN MSDU50 Preventive Maintenance and Troubleshooting Preventive Maintenance TroubleshootingComputer Panel Open Interface Board Visible Fryer Heating Oil Computer Panel Open Interface Board VisibleFrom Preceeding From Preceeding Is the AL LED illuminated? Controller Panel Open Interface Board Visible From Preceeding From Preceeding Pump Motor Actuation Filter System OperationService Procedures Replace ControllerReplace Interface Board Replace Temperature Probe Replace TransformerReplace Temperature Probe Replace Heating Element Replace Heating Element Remove the element mounting screws Left element- 9-pin Right element- 6-pin Connector Replace HIGH-LIMIT Replace Frypot Replace Contactor Contactor mounting screws BUILT-IN Filter System Service Procedures Filtration Problem ResolutionBUILT-IN Filter System Service Procedures FootPrint III Wiring Diagram Electric Interface Board Diagnostic Chart Diagnostic LED LegendSimplified Wiring DiagramsCommon Electric McDONALDS H14 SERIES- FULL-VAT Common Electric McDONALDS H14 SERIES- DUAL-VAT GNDCommon Electric McDONALDS H14 SERIES- FULL-VAT- Export WYE Common Electric McDONALDS H14 SERIES- DUAL-VAT- Export WYE Wiring DIAGRAMS, Main McDonald’s DomesticMcDonald’s European Community CE McDonald’s European Community CE Prior To 9/98 McDonald’s European Community CE XBIH14 McDonald’s Domestic Contactor McDonald’s European Community CE WYE Contactor McDonald’s European Community CE XBIH14 Contactor McDonald’s 440/480V Contactor McDonald’s Delta CSA Contactor McDonald’s Domestic Control Cord McDonald’s English Control Cord Footprint III, Late Configuration Wiring DIAGRAMS, Filter UnitsFootprint III, Early Configuration H14 Series Electric Fryers Parts List AccessoriesPage Side , Cabinet 2 MH/BIH214, 314, 414, 514 Cabinet Assemblies Component Casters, Legs and Associated Hardware Component Box Assemblies/Associated Component Parts Page Control Panel Assembly Door Assembly Components Controller Assemblies Drain System Components Page McDonald’s Domestic, Dual-vat Elements and Related Components Component Hood Relay Box, Power Cords and Hood Cords Filter Base/Pan Assemblies 8.9.1 Filter Base Assemblies Filter Base Assembly, FootPrint Filter Pan Assemblies Filter Pan Assembly, Single FootPrint Filter Pump and Motor Assemblies Pump and Motor Assembly, 250V 50/60 Hz Page Flex Line Assembly, With Male/Female Ends Oil Return Linkage Assemblies and Components Frypot Assemblies and Drain Valve Components Thermostats and Related Components
Top Page Image Contents