Venting Requirements
(vented models only)
■ | Vent system must terminate to the outdoors, except for non- |
| vented (recirculating) installations. |
■ | Do not terminate the vent system in an attic or other enclosed |
Roof Venting | Wall Venting |
|
|
| (recirculating) |
area. |
■ Do not use 4" (10.2 cm) |
■ Use metal vent only. Rigid metal vent is recommended. |
Plastic or metal foil vent is not recommended. |
■ The length of vent system and number of elbows should be |
kept to a minimum to provide efficient performance. |
For the most efficient and quiet operation:
■ Use no more than three 90° elbows. |
■ Make sure there is a minimum of 24" (61 cm) of straight vent |
between the elbows if more than 1 elbow is used. |
■ Do not install 2 elbows together. |
■ Use clamps to seal all joints in the vent system. |
The vent system must have a damper. If the roof or wall cap |
B |
AA
B 
B
A
■ |
has a damper, do not use the damper supplied with the range |
hood. |
■ Use caulking to seal exterior wall or roof opening around the |
cap. |
■ The size of the vent should be uniform. |
Cold Weather Installations
An additional back draft damper should be installed to minimize backward cold air flow and a thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.
The break should be as close as possible to where the vent system enters the heated portion of the house.
Makeup Air
Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your area.
A. Roof cap | A. Wall cap | A. Deflector |
B. 6" (15.2 cm) | B. 6" (15.2 cm) | B. 6" (15.2 cm) |
round vent | round vent | round vent |
Calculating Vent System Length
To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.
Vent Piece | 6" (15.2 cm) Round |
45° elbow | 2.5 ft |
| (0.8 m) |
90° elbow | 5.0 ft |
| (1.5 m) |
Maximum equivalent vent length is 35 ft (10.7 m).
Venting Methods
This canopy hood is factory set for venting through the roof or wall.
A 6" (15.2 cm) round vent system is needed for installation (not included). The hood exhaust opening is 6" (15.2 cm) round.
NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance.
Vent system can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.
Rear discharge
A 90° elbow may be installed immediately above the hood.
For Non-Vented (recirculating) Installations
If it is not possible to vent cooking fumes and vapors to the outside, the hood can be used in the
Example vent system
90 elbow |
|
|
|
|
|
| Wall cap | ||
|
| 6 ft (1.8 m) |
|
| |||||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2ft
(0.6 m)
The following example falls within the maximum recommended vent length of 35 ft (10.7 m).
1 | - 90° elbow | = 5.0 ft (1.5 m) |
1 | - wall cap | = 0.0 ft (0.0 m) |
8 ft (2.4 m) straight | = 8.0 ft (2.4 m) | |
|
| |
Length of system | = 13.0 ft (3.9 m) | |
|
|
|
6