K-Tec MT2000 manual Table of Contents

Page 2

TABLE OF CONTENTS

1.	INTRODUCTION			4
2. OVERVIEW				5
	2.1 Storage Information			5
	2.2	Ambient Temperature		5
	2.3	Description & Principle of Operation		5
		2.3.1	Direct Reflect Mode (standard)	5
		2.3.2	Ultra Low Dielectric (ULD) Measure Method	6
3.	INSTALLATION			7
	3.1	Mounting Requirements		7
	3.2	Shortening of Probe		8
	3.3	MT2000 Guided Wave Radar Guidelines		8
	3.4	Wiring		9
	3.5	ATEX Approval Information		9
4. COMMISSIONING				9
	4.1	Quickstart Procedure		9
	4.2	Verify Proper Power-Up		10
	4.3	Setting the 4mA and 20mA Points Using the Pushbutton Menu		10
		4.3.1 LCD Menu Operation		11
	4.4	Detailed Configuration Parameters		12
		4.4.1	Direct Mode Blanking Parameter (BLK)	12
		4.4.2	Threshold Level Parameter (THV) and Gain Setting (GS)	12
		4.4.3	Advanced Parameter Settings	13
		4.4.4	Ultra Low Dielectric (ULD) Mode Configuration	15
	4.5	Advanced Output Configuration		16
		4.5.1 DAC Trim		16
		4.5.2	Setting the DAC Trim	16
		4.5.3	Displayed Engineering Units (EUN)	16
		4.5.4 4 - 20 mA Output Damping (DMP)		16
		4.5.5 Bench Calibration of the 4mA & 20mA Points		17
		4.5.6	4mA & 20mA Calibration Using Actual Level Input	17
		4.5.7	Reversing the Output Action Using Actual Level Input	18
		4.5.8	Jumper Switch Settings	18
5. TROUBLESHOOTING INFORMATION				19
	5.1	Valid Current Loop Outputs		19
	5.2	Possible Symptoms		19
	5.3	Electronics Module Replacement		20
6. HONEYWELL DE OUTPUT OPTION				20
	6.1	Interoperability and Conformance Class		20
	6.2	Operating Modes		21
7. HART PROTOCOL INTERFACE OPTION				21
	7.1	268 ROSEMOUNT Communicator		21
	7.2	HART AMS		21
		7.2.1	Compatibility	21
		7.2.2	Resource Files	21
8. GLOSSARY OF TERMS				22

2	MT2000-0200-01 Rev f (10-2007) DCN0160

Image 2

Contents Guided Wave Radar Level Transmitter Table of Contents List of Figures AppendicesIntroduction Storage Information Ambient TemperatureOverview Measurement cycle consists of the followingDirect Reflect Mode standard cont’d Ultra Low Dielectric ULD Measure MethodInstallation Mounting RequirementsMT2000 Guided Wave Radar Guidelines Factory Default ConfigurationShortening of Probe URV = Probe Length LRV = 0 in. / 0 mmCommissioning WiringQuickstart Procedure MT2000 Guided Wave Radar Guidelines cont’dSetting the 4mA and 20 mA Points Using the Pushbutton Menu Quickstart Procedure cont’dVerify Proper Power-Up LCD Menu Operation Calibration MenuDetailed Configuration Parameters Direct Mode Blanking Menu Threshold Level Parameter THV and Gain Setting GSL1O Threshold Level Parameter THV and Gain Setting GS cont’dAdvanced Parameter Settings Advanced Parameter Settings cont’d KO & KGDC = I + H L / H2 Ultra Low Dielectric ULD Mode Configuration= H * Sqrt DC H + L Setting the DAC trim Ultra Low Dielectric ULD Mode Configuration cont’dAdvanced Output Configuration DAC TrimFigure6 4mA & 20mA Calibration Using Actual Level Input Bench Calibration of the 4mA & 20mA PointsReversing The Output Action Using Actual Level Input Jumper Switch SettingsValid Current Loop Outputs Troubleshooting InformationPossible Symptoms Honeywell DE Output Option Possible Symptoms cont’dElectronics Module Replacement Interoperability and Conformance ClassHart Communicator Hart Protocol Interface OptionOperating Modes CompatibilityGlossary of Terms LRVAppendices Appendix a Sensor TrimConfiguration 2 Hidden Menu END CFG MenuTMP Appendix C Linearization To access the linearization tableSetting up Linearization Table Points To clear the linearization tableAppendix D Interface Applications MT2000 InterfacePrerequisites Use and setup of the oscilloscope for the MT2000Scope Settings Channel a Channel BAppendix F CE Certificate of Conformity Appendix G Exida Certificate MT2000-0200-1 Rev f 10-2007 DCN0160 MT2000-0200-01 Rev f 10-2007 DCN0160 MT2000-0200-1 Rev f 10-2007 DCN0160 10a Appendix I Mounting Configurations3a, 3b 10bAppendix J Warranty Statement Year Warranty for