K-Tec MT2000 manual List of Figures, Appendices

Page 3

TABLE OF CONTENTS (CONTINUED)

9. APPENDICES			23
9.1	APPENDIX A: Sensor Trim		23
9.2	APPENDIX B: Additional Special Functions in the CFG2 (Hidden) Menu		24
9.3	APPENDIX C: Linearization		26
9.4	APPENDIX D: Interface Applications		27
9. 5	APPENDIX E: Oscilloscope Use & Setup for Troubleshooting		28
	9.5.1	General Setup	28
	9.5.2	Use and Setup of the Oscilloscope for the MT2000	28
9. 6	APPENDIX F: CE Certification of Conformity		29
9. 7	APPENDIX G: Exida Certificate		30
9.8	APPENDIX H: Installation Drawings for Intrinsic Safety & Standard Wiring		31
9.9	APPENDIX I: Mounting Configurations		34
9.10 APPENDIX J: Warranty Statement			35
Figure 2.1	Direct Reflect Mode		6

LIST OF FIGURES

Figure 3.1	Mounting Requirements	7
Figure 3.2	Factory Default Configuration	8
Figure 4.1	Quikstart Procedure	10
Figure 4.2	Electronics LCD Display	10
Figure 4.3	Transmitter Configuration from Model Number	12
Figure 4.4	L10 Advanced Parameter Settings	13
Figure 4.5	Ultra Low Dielectric (ULD) Mode Configuration	16
Figure 4.6	Example of Display in Calibration Mode	18
Figure 4.7	Write Project (right jumper)	18
Figure 9.1	Sensor Trim (Factory Defaults)	23
Figure 9.2	Configuration 2 (hidden) Menu	24
Figure 9.3	MT2000 Interface	27
Figure 9.4	Oscilloscope Use & Setup for Troubleshooting	28
Figure 9.5	Mounting Configurations	31

MT2000-0200-1 Rev f (10-2007) DCN0160

3

Image 3

Contents Guided Wave Radar Level Transmitter Table of Contents Appendices List of FiguresIntroduction Measurement cycle consists of the following Ambient TemperatureOverview Storage InformationUltra Low Dielectric ULD Measure Method Direct Reflect Mode standard cont’dMounting Requirements InstallationURV = Probe Length LRV = 0 in. / 0 mm Factory Default ConfigurationShortening of Probe MT2000 Guided Wave Radar GuidelinesMT2000 Guided Wave Radar Guidelines cont’d WiringQuickstart Procedure CommissioningQuickstart Procedure cont’d Verify Proper Power-UpSetting the 4mA and 20 mA Points Using the Pushbutton Menu Calibration Menu LCD Menu OperationThreshold Level Parameter THV and Gain Setting GS Detailed Configuration Parameters Direct Mode Blanking MenuThreshold Level Parameter THV and Gain Setting GS cont’d Advanced Parameter SettingsL1O KO & KG Advanced Parameter Settings cont’dUltra Low Dielectric ULD Mode Configuration = H * Sqrt DC H + LDC = I + H L / H2 DAC TrimFigure Ultra Low Dielectric ULD Mode Configuration cont’dAdvanced Output Configuration Setting the DAC trimBench Calibration of the 4mA & 20mA Points 6 4mA & 20mA Calibration Using Actual Level InputJumper Switch Settings Reversing The Output Action Using Actual Level InputTroubleshooting Information Possible SymptomsValid Current Loop Outputs Interoperability and Conformance Class Possible Symptoms cont’dElectronics Module Replacement Honeywell DE Output OptionCompatibility Hart Protocol Interface OptionOperating Modes Hart CommunicatorLRV Glossary of TermsAppendix a Sensor Trim AppendicesEND CFG Menu Configuration 2 Hidden MenuTMP To clear the linearization table To access the linearization tableSetting up Linearization Table Points Appendix C LinearizationMT2000 Interface Appendix D Interface ApplicationsChannel B Use and setup of the oscilloscope for the MT2000Scope Settings Channel a PrerequisitesAppendix F CE Certificate of Conformity Appendix G Exida Certificate MT2000-0200-1 Rev f 10-2007 DCN0160 MT2000-0200-01 Rev f 10-2007 DCN0160 MT2000-0200-1 Rev f 10-2007 DCN0160 10b Appendix I Mounting Configurations3a, 3b 10aYear Warranty for Appendix J Warranty Statement