Maytag W10401504D Prepare Dishwasher, Option D, No waste disposer with air gap

Page 11

Option D, No waste disposer – with air gap

1.Connect rubber end of drain hose to

air gap and cut if needed. NOTE: Do not cut ribbed section.

2.Attach drain hose to air gap with

large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to 5 cm) screw-type clamp (not provided).

3.Use a rubber hose (not provided)

with screw-type clamps (not provided) to connect from waste tee to air gap.

Prepare Dishwasher

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

Remove and discard the foam blocks located above the front legs on each side of the dishwasher. The blocks cover the rope/link pulleys on the dishwasher.

Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not use door panel as a worktable without first covering with a towel to avoid scratching the door panel.

11

Image 11
Contents W10401504D Dishwasher Safety Table of ContentsTools and Parts Installation RequirementsAll Installations Addition, for first-time installationsLocation Requirements Page Water Supply Requirements If connecting dishwasher with a power supply cordIf connecting dishwasher with direct wiring Drain RequirementsPrepare Cabinet Opening-New Utilities Installation InstructionsPrepare Cabinet Opening Existing Utilities Prepare and Route Water Line Option B, Direct WireInstall Drain Hose Option C, Waste disposer with air gap Option A, Waste disposer no air gapOption B, No waste disposer no air gap Option D, No waste disposer with air gap Prepare DishwasherPage Make Power Supply Cord Connection Determine Cabinet Opening Option A, Countertop Attachment Choose Attachment OptionPush the plastic buttons out of the side of the tub Move Dishwasher Close to Cabinet OpeningPage Connect to Water Supply Connect to Drain Make Direct Wire Electrical Connection Secure Dishwasher in Cabinet Opening Side mount dishwasher to cabinet Secure dishwasher to countertopReconnect Power Complete InstallationAdditional Tips Check OperationIf Dishwasher Does Not Operate Il faut Table DES MatièresSécurité DU LAVE-VAISSELLE Outillage et pièces Exigences DinstallationToutes les installations Exigences demplacement Page Pour le raccordement direct du lave-vaisselle Exigences d’évacuationSpécifications de l’alimentation en eau Spécifications électriquesOption A, cordon d’alimentation Instructions DinstallationPréparation et acheminement de l’alimentation électrique Option B, raccordement direct Préparation et acheminement de la Canalisation d’eauInstallation du tuyau d’évacuation Option C, Broyeur à déchets avec brise-siphon Option A, Broyeur à déchets sans brise-siphonOption B, Pas de broyeur à déchets sans brise-siphon Option D, Pas de broyeur à déchets avec brise-siphon Préparation du lave-vaissellePage Raccordement du cordon dalimentation Évaluation de l’ouverture dencastrement Du placard Option A, Fixation au plan de travail Choix de l’option de fixationAvertissement Remarques Raccordement à l’alimentation en eau Raccordement au circuit dévacuation Raccordement électrique direct Page Fixation latérale du lave-vaisselle au placard Fixation du lave-vaisselle au plan de travailRétablir la source de courant électrique Achever linstallationConseils supplémentaires Contrôle du fonctionnementSi le lave-vaisselle ne fonctionne pas W10401504D