Maytag W10401504D installation instructions Install Drain Hose

Page 9

Attach the water supply line (copper tubing or flexible braided line) to the hot water line using a connection configuration that is in compliance with local codes and ordinances. The water supply to the dishwasher should have a manual shutoff valve located under the sink.

Slowly route water supply line through hole in cabinet. (If you are using copper tubing, it will bend and kink easily, so be gentle.) It should be far enough into the cabinet opening to connect it to the dishwasher inlet on the front left side of the dishwasher.

Slowly turn water shutoff valve to “ON” position. Flush water into a shallow pan until clear to get rid of particles that could clog the inlet valve. Turn shutoff valve to “OFF” position.

Route water line and tape it to the floor in area shown. This will keep it from moving when dishwasher is moved into cabinet opening.

Install Drain Hose

IMPORTANT: Always use a new drain hose. Check local codes to determine whether an air gap is required.

If needed, drill a 1¹⁄₂" (3.8 cm) diameter hole in cabinet wall or side of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the front center of opening where drain connection will be made. Tape drain hose to the floor in area shown. This will prohibit it from moving when dishwasher is moved into cabinet opening.

9

Image 9
Contents W10401504D Dishwasher Safety Table of ContentsAll Installations Installation RequirementsAddition, for first-time installations Tools and PartsLocation Requirements Page If connecting dishwasher with direct wiring If connecting dishwasher with a power supply cordDrain Requirements Water Supply RequirementsInstallation Instructions Prepare Cabinet Opening Existing UtilitiesPrepare Cabinet Opening-New Utilities Prepare and Route Water Line Option B, Direct WireInstall Drain Hose Option A, Waste disposer no air gap Option B, No waste disposer no air gapOption C, Waste disposer with air gap Option D, No waste disposer with air gap Prepare DishwasherPage Make Power Supply Cord Connection Determine Cabinet Opening Option A, Countertop Attachment Choose Attachment OptionPush the plastic buttons out of the side of the tub Move Dishwasher Close to Cabinet OpeningPage Connect to Water Supply Connect to Drain Make Direct Wire Electrical Connection Secure Dishwasher in Cabinet Opening Side mount dishwasher to cabinet Secure dishwasher to countertopReconnect Power Complete InstallationCheck Operation If Dishwasher Does Not OperateAdditional Tips Table DES Matières Sécurité DU LAVE-VAISSELLEIl faut Exigences Dinstallation Toutes les installationsOutillage et pièces Exigences demplacement Page Spécifications de l’alimentation en eau Exigences d’évacuationSpécifications électriques Pour le raccordement direct du lave-vaisselleInstructions Dinstallation Préparation et acheminement de l’alimentation électriqueOption A, cordon d’alimentation Option B, raccordement direct Préparation et acheminement de la Canalisation d’eauInstallation du tuyau d’évacuation Option A, Broyeur à déchets sans brise-siphon Option B, Pas de broyeur à déchets sans brise-siphonOption C, Broyeur à déchets avec brise-siphon Option D, Pas de broyeur à déchets avec brise-siphon Préparation du lave-vaissellePage Raccordement du cordon dalimentation Évaluation de l’ouverture dencastrement Du placard Option A, Fixation au plan de travail Choix de l’option de fixationAvertissement Remarques Raccordement à l’alimentation en eau Raccordement au circuit dévacuation Raccordement électrique direct Page Fixation latérale du lave-vaisselle au placard Fixation du lave-vaisselle au plan de travailRétablir la source de courant électrique Achever linstallationContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pasConseils supplémentaires W10401504D