Maytag W10199707A installation instructions Connect to Water Supply

Page 16

9 Check for plumb and adjust legs if needed

Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the front panel. Check that dishwasher is centered from front to back in the opening. If needed, adjust leveling leg until dishwasher is plumb. Repeat for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise dishwasher off the ground to adjust front legs. With some installations, it may be easier to adjust the front leg using the 3/16" hex head socket or adjustable wrench.

Preferred method

Optional method

10 Check level side to side and adjust legs if needed

Place level against top front opening of tub. Check that dishwasher is level from side to side. If dishwasher is not level, adjust front legs up or down until dishwasher is level.

16

Connect to Water Supply

1 Slide nut and ferrule onto tubing

Nut

Ferrule

Copper tubing only: Slide nut then ferrule onto copper tubing about 1" (2.5 cm).

NOTE: To avoid vibration during operation, route the water supply line so that it does not touch the dishwasher base, frame or motor.

2 Connect water supply using copper or flexible line

Copper tubing only: Put the tubing into the 90° elbow fitting as far as it will go (the copper tubing bends and kinks easily). Slide the nut and ferrule forward and start the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using 5/8" open ended wrench or adjustable wrench.

NOTE: Do not use Teflon® tape with compression fittings.

3 Tighten copper or braided tubing connection

Hold the 90° elbow fitting still with one adjustable wrench and tighten the nut with second adjustable wrench.

Helpful Tip: Use a 5/8" open ended wrench for easier access to tighten connection.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents W10199707A Table of Contents You Need toTools and Parts Location Requirements Product and Cabinet Opening Dimensions RemovedDrain Requirements Water Supply RequirementsElectrical Requirements Use of air gapPrepare Cabinet Opening-Existing Utilities Prepare Cabinet Opening-New UtilitiesPrepare and Route Water Line Install Drain Hose Install moisture barrier on some models Install moisture barrier on some modelsNo waste disposer no air gap Waste disposer with air gapPrepare Dishwasher Make Power Supply Cord Connection Power Cord-Route cord into terminal boxPower Supply Cord- Connect ground wire Power Cord-Connect remaining wiresDetermine Cabinet Opening Install the Door Handle on some models Move Dishwasher into Cabinet OpeningCheck water and drain hose position Open and close doorCloses too quickly Decrease spring tension Door falls open Increase spring tensionConnect to Water Supply Make Direct Wire Electrical Connection Slide clamp onto connectorDirect Wire--Route cable into terminal box Connect to DrainDirect Wire-Connect ground wire Direct Wire-Connect remaining wiresDirect Wire-Secure cable in strain relief Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Complete Installation Power supply cord-Plug into a grounded 3 prong outlet Reconnect powerCheck Operation If Dishwasher Does Not OperatePage Table des matières Il fautOutillage et pièces Exigences demplacement Espacelibre Exigences dévacuation Spécifications de l’alimentation en eauSpécifications électriques Utilisation du dispositif de brise-siphonInterromprelalimentation électrique Fermeture de lalimentation en eauLutilisateur possède-t-il déjà des moyens de raccordement? Quel type de connexion lutilisateur emploie-t-il?Préparation et acheminement de la canalisation d’eau Cordon dalimentation électrique Préparation du trouPerçage du trou Raccordement direct Préparation du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets avec brise-siphon Pas de broyeur à déchets sans brise-siphonBroyeur à déchets avec brise-siphon Préparation du lave-vaisselle Placer le lave-vaisselle sur le dosDépose des panneaux Application de ruban adhésif Téflon ou composé détanchéitéInstallation dun serre-câble Raccordement du cordon dalimentationConfiguration du câblage Évaluation de l’ouverture dencastrement du placardMesure de louverture dencastrement du placard Tableau de réglage de la hauteur du lave-vaisselleInstallation de la poignée de porte sur certains modèles Installation de la poignée de porteDéplacement du lave-vaisselle à proximité de louverture Planchers surélevés Ajouter des cales si nécessaireOuverture et fermeture de la porte Insertion du lave-vaisselle dans louverture du placardMéthode recommandée Méthode facultative Raccordement à l’alimentation en eauVérification de laplomb et réglage des pieds si nécessaire Enfiler lécrou et la virole sur la canalisationRaccordement au circuit dévacuation Enfilement de la bride sur le raccordRecherche de fuites Position définitive de la bride de tuyauRaccordement direct Raccordement du fil de mise à la terre Raccordement électrique directRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Achever linstallation Inspection de la rive de panneau inférieure Serrage des visReconnexion de lalimentation électrique Rétablir l’alimentation électriqueSi le lave-vaisselle ne fonctionne pas correctement Contrôle du fonctionnementConseils supplémentaires

W10199707A specifications

The Maytag W10199707A is a remarkable replacement water filter designed to enhance the performance of various refrigerator models. As a vital component for ensuring clean and safe drinking water, this filter is engineered with several key features and technologies that set it apart in the market.

One of the standout characteristics of the Maytag W10199707A is its advanced filtration technology. This product is designed to reduce contaminants, such as chlorine taste and odor, lead, and other harmful chemicals. This provides not only better-tasting water but also peace of mind for consumers looking for a reliable filtration option. The filter utilizes activated carbon to absorb impurities effectively, making it a crucial addition to any modern refrigerator system.

Installation and maintenance are made simple with the Maytag W10199707A. The filter is designed for easy replacement, typically requiring no tools for installation. Users can quickly swap out the old filter with a new one, ensuring that their water remains fresh and clean without unnecessary hassle. Additionally, the filter has a lifespan of about six months, depending on usage, which allows for convenient long-term operation without frequent changes.

Another significant feature of the Maytag W10199707A is its compatibility with various refrigerator models from leading brands. This versatility ensures that many consumers can benefit from this filter, regardless of their refrigerator brand, making it a popular choice for families and households.

Durability and reliability are fundamental principles behind the design of the Maytag W10199707A. Built to withstand daily use, the filter maintains optimal performance well throughout its lifespan. Each filter is rigorously tested to meet high-quality standards, ensuring it effectively meets consumer needs for safe and clean drinking water.

In conclusion, the Maytag W10199707A water filter stands out due to its advanced filtration technology, ease of installation, and compatibility with numerous refrigerator models. For anyone seeking to enhance their home’s water quality, this filter represents a reliable and efficient option that prioritizes health and convenience. Investing in this water filter is a smart choice for ensuring a consistent supply of refreshing and safe drinking water.
Top Page Image Contents