Maytag W10199707A Drain Requirements, Water Supply Requirements, Electrical Requirements

Page 6

Drain Requirements

A new drain hose is supplied with your dishwasher.

If drain hose is not long enough, use a new drain hose with a maximum length of 12’ (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.

Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20"

(50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.

Use of air gap

Air gap

Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor.

Use 1/2" minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance with the air gap installation instructions. When you are connecting the air gap a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Water Supply Requirements

A hot water line with 20-120 psi (138-862 kPa) water pressure can be verified by a licensed plumber.

120°F (49°C) water at dishwasher.

3/8" O.D. copper tubing with compression fitting or flexible braided water supply line

(Part Number 4396897RP)

NOTE: 1/2" minimum plastic tubing is not recommended.

A 90° elbow with 3/8" N.P.T. external pipe threads on one end.

Do not solder within 6" (15.2 cm) from water inlet valve.

6

Electrical Requirements

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association

One Batterymarch Park Quincy, MA 02269

You must have:

120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical supply.

copper wire only.

We recommend:

a time-delay fuse or circuit breaker.

a separate circuit.

If connecting dishwasher with a power supply cord:

Use UL listed power supply cord kit (Part No. 4317824) marked for use with dishwasher.

Power supply cord must plug into

a grounded 3 prong outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.

If connecting dishwasher with direct wiring:

Use flexible, armored or nonmetallic

sheathed, copper wire with grounding wire

that meets the wiring requirements for your home and local codes and ordinances.

Use a UL listed or CSA approved strain relief.

Image 6
Contents W10199707A Table of Contents You Need toTools and Parts Location Requirements Product and Cabinet Opening Dimensions RemovedElectrical Requirements Drain RequirementsWater Supply Requirements Use of air gapPrepare Cabinet Opening-Existing Utilities Prepare Cabinet Opening-New UtilitiesPrepare and Route Water Line Install Drain Hose No waste disposer no air gap Install moisture barrier on some modelsInstall moisture barrier on some models Waste disposer with air gapPrepare Dishwasher Power Supply Cord- Connect ground wire Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Power Cord-Connect remaining wiresDetermine Cabinet Opening Install the Door Handle on some models Move Dishwasher into Cabinet OpeningCloses too quickly Decrease spring tension Check water and drain hose positionOpen and close door Door falls open Increase spring tensionConnect to Water Supply Direct Wire--Route cable into terminal box Make Direct Wire Electrical ConnectionSlide clamp onto connector Connect to DrainDirect Wire-Secure cable in strain relief Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Complete Installation Check Operation Power supply cord-Plug into a grounded 3 prong outletReconnect power If Dishwasher Does Not OperatePage Table des matières Il fautOutillage et pièces Exigences demplacement Espacelibre Spécifications électriques Exigences dévacuationSpécifications de l’alimentation en eau Utilisation du dispositif de brise-siphonLutilisateur possède-t-il déjà des moyens de raccordement? Interromprelalimentation électriqueFermeture de lalimentation en eau Quel type de connexion lutilisateur emploie-t-il?Perçage du trou Préparation et acheminement de la canalisation d’eauCordon dalimentation électrique Préparation du trou Raccordement direct Préparation du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets sans brise-siphon Pas de broyeur à déchets avec brise-siphonBroyeur à déchets avec brise-siphon Dépose des panneaux Préparation du lave-vaissellePlacer le lave-vaisselle sur le dos Application de ruban adhésif Téflon ou composé détanchéitéInstallation dun serre-câble Raccordement du cordon dalimentationMesure de louverture dencastrement du placard Configuration du câblageÉvaluation de l’ouverture dencastrement du placard Tableau de réglage de la hauteur du lave-vaisselleDéplacement du lave-vaisselle à proximité de louverture Installation de la poignée de porte sur certains modèlesInstallation de la poignée de porte Planchers surélevés Ajouter des cales si nécessaireOuverture et fermeture de la porte Insertion du lave-vaisselle dans louverture du placardVérification de laplomb et réglage des pieds si nécessaire Méthode recommandée Méthode facultativeRaccordement à l’alimentation en eau Enfiler lécrou et la virole sur la canalisationRecherche de fuites Raccordement au circuit dévacuationEnfilement de la bride sur le raccord Position définitive de la bride de tuyauRaccordement électrique direct Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Achever linstallation Reconnexion de lalimentation électrique Inspection de la rive de panneau inférieureSerrage des vis Rétablir l’alimentation électriqueContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pas correctementConseils supplémentaires

W10199707A specifications

The Maytag W10199707A is a remarkable replacement water filter designed to enhance the performance of various refrigerator models. As a vital component for ensuring clean and safe drinking water, this filter is engineered with several key features and technologies that set it apart in the market.

One of the standout characteristics of the Maytag W10199707A is its advanced filtration technology. This product is designed to reduce contaminants, such as chlorine taste and odor, lead, and other harmful chemicals. This provides not only better-tasting water but also peace of mind for consumers looking for a reliable filtration option. The filter utilizes activated carbon to absorb impurities effectively, making it a crucial addition to any modern refrigerator system.

Installation and maintenance are made simple with the Maytag W10199707A. The filter is designed for easy replacement, typically requiring no tools for installation. Users can quickly swap out the old filter with a new one, ensuring that their water remains fresh and clean without unnecessary hassle. Additionally, the filter has a lifespan of about six months, depending on usage, which allows for convenient long-term operation without frequent changes.

Another significant feature of the Maytag W10199707A is its compatibility with various refrigerator models from leading brands. This versatility ensures that many consumers can benefit from this filter, regardless of their refrigerator brand, making it a popular choice for families and households.

Durability and reliability are fundamental principles behind the design of the Maytag W10199707A. Built to withstand daily use, the filter maintains optimal performance well throughout its lifespan. Each filter is rigorously tested to meet high-quality standards, ensuring it effectively meets consumer needs for safe and clean drinking water.

In conclusion, the Maytag W10199707A water filter stands out due to its advanced filtration technology, ease of installation, and compatibility with numerous refrigerator models. For anyone seeking to enhance their home’s water quality, this filter represents a reliable and efficient option that prioritizes health and convenience. Investing in this water filter is a smart choice for ensuring a consistent supply of refreshing and safe drinking water.