Maytag W10199707A installation instructions Install Drain Hose

Page 9

3 Route water supply line

Slowly route water supply line through hole in cabinet. (If using copper tubing, it will bend and kink easily, so be gentle.) It should be far enough into the cabinet opening to connect it to the dishwasher inlet on the front left side of the dishwasher.

4 Flush water supply line

Slowly turn water shutoff valve to “ON” position. Flush water into a shallow pan until clear to get rid of particles that could clog the inlet valve. Turn shutoff valve to “OFF” position.

Install Drain Hose

IMPORTANT: Always use a new drain hose. Check local codes to determine if an air gap is required.

1 Drill hole

1 1/2”

(3.8 cm)

If needed, drill a 1 1/2" (3.8 cm) diameter hole in cabinet wall or side of the opening closest to the sink.

2 Route drain hose

Drain hose

Route drain hose as shown through hole in cabinet to the front center of opening where drain connection will be made. Tape drain hose to the floor in area shown. This will prohibit it from moving when dishwasher is moved into cabinet opening.

3 Connect drain hose

Connect drain hose to waste tee or waste disposer using one of the following options:

Option A, Waste disposer – no air gap

Option B, No waste disposer – no air gap

Option C, Waste disposer – with air gap

Option D, No waste disposer – with air gap

IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20" (50.8 cm) above the floor where the dishwasher will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away from the floor.

Option A, Waste disposer – no air gap

Waste disposer – no air gap

Disposer inlet

 

Large silver

 

drain hose clamp

 

 

Drain hose

 

 

 

Drain trap

1

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle nose pliers to remove

2 plug.

3

3. Attach drain hose to disposer inlet

with large silver drain hose clamp

(provided). Use pliers to squeeze clamp open and move into position.

9

Image 9
Contents W10199707A You Need to Table of ContentsTools and Parts Location Requirements Removed Product and Cabinet Opening DimensionsWater Supply Requirements Drain RequirementsElectrical Requirements Use of air gapPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Install Drain Hose Install moisture barrier on some models Install moisture barrier on some modelsNo waste disposer no air gap Waste disposer with air gapPrepare Dishwasher Power Cord-Route cord into terminal box Make Power Supply Cord ConnectionPower Supply Cord- Connect ground wire Power Cord-Connect remaining wiresDetermine Cabinet Opening Move Dishwasher into Cabinet Opening Install the Door Handle on some modelsOpen and close door Check water and drain hose positionCloses too quickly Decrease spring tension Door falls open Increase spring tensionConnect to Water Supply Slide clamp onto connector Make Direct Wire Electrical ConnectionDirect Wire--Route cable into terminal box Connect to DrainDirect Wire-Connect remaining wires Direct Wire-Connect ground wireDirect Wire-Secure cable in strain relief Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Complete Installation Reconnect power Power supply cord-Plug into a grounded 3 prong outletCheck Operation If Dishwasher Does Not OperatePage Il faut Table des matièresOutillage et pièces Exigences demplacement Espacelibre Spécifications de l’alimentation en eau Exigences dévacuationSpécifications électriques Utilisation du dispositif de brise-siphonFermeture de lalimentation en eau Interromprelalimentation électriqueLutilisateur possède-t-il déjà des moyens de raccordement? Quel type de connexion lutilisateur emploie-t-il?Cordon dalimentation électrique Préparation du trou Préparation et acheminement de la canalisation d’eauPerçage du trou Raccordement direct Préparation du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets sans brise-siphon Pas de broyeur à déchets avec brise-siphonBroyeur à déchets avec brise-siphon Placer le lave-vaisselle sur le dos Préparation du lave-vaisselleDépose des panneaux Application de ruban adhésif Téflon ou composé détanchéitéRaccordement du cordon dalimentation Installation dun serre-câbleÉvaluation de l’ouverture dencastrement du placard Configuration du câblageMesure de louverture dencastrement du placard Tableau de réglage de la hauteur du lave-vaisselleInstallation de la poignée de porte Installation de la poignée de porte sur certains modèlesDéplacement du lave-vaisselle à proximité de louverture Planchers surélevés Ajouter des cales si nécessaireInsertion du lave-vaisselle dans louverture du placard Ouverture et fermeture de la porteRaccordement à l’alimentation en eau Méthode recommandée Méthode facultativeVérification de laplomb et réglage des pieds si nécessaire Enfiler lécrou et la virole sur la canalisationEnfilement de la bride sur le raccord Raccordement au circuit dévacuationRecherche de fuites Position définitive de la bride de tuyauRaccordement électrique direct Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Achever linstallation Serrage des vis Inspection de la rive de panneau inférieureReconnexion de lalimentation électrique Rétablir l’alimentation électriqueContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pas correctementConseils supplémentaires

W10199707A specifications

The Maytag W10199707A is a remarkable replacement water filter designed to enhance the performance of various refrigerator models. As a vital component for ensuring clean and safe drinking water, this filter is engineered with several key features and technologies that set it apart in the market.

One of the standout characteristics of the Maytag W10199707A is its advanced filtration technology. This product is designed to reduce contaminants, such as chlorine taste and odor, lead, and other harmful chemicals. This provides not only better-tasting water but also peace of mind for consumers looking for a reliable filtration option. The filter utilizes activated carbon to absorb impurities effectively, making it a crucial addition to any modern refrigerator system.

Installation and maintenance are made simple with the Maytag W10199707A. The filter is designed for easy replacement, typically requiring no tools for installation. Users can quickly swap out the old filter with a new one, ensuring that their water remains fresh and clean without unnecessary hassle. Additionally, the filter has a lifespan of about six months, depending on usage, which allows for convenient long-term operation without frequent changes.

Another significant feature of the Maytag W10199707A is its compatibility with various refrigerator models from leading brands. This versatility ensures that many consumers can benefit from this filter, regardless of their refrigerator brand, making it a popular choice for families and households.

Durability and reliability are fundamental principles behind the design of the Maytag W10199707A. Built to withstand daily use, the filter maintains optimal performance well throughout its lifespan. Each filter is rigorously tested to meet high-quality standards, ensuring it effectively meets consumer needs for safe and clean drinking water.

In conclusion, the Maytag W10199707A water filter stands out due to its advanced filtration technology, ease of installation, and compatibility with numerous refrigerator models. For anyone seeking to enhance their home’s water quality, this filter represents a reliable and efficient option that prioritizes health and convenience. Investing in this water filter is a smart choice for ensuring a consistent supply of refreshing and safe drinking water.