Bunn FCD-4 manual Cleaning Monthly Clean Condenser Air Filter, Annually Replace Pump Tubing

Page 13

CLEANING (cont)

Monthly: Clean Condenser Air Filter

1.Remove the condenser air filter located on the rear of the dispenser.

2.Using a water spray, clean the air filter.

Annually: Replace Pump Tubing

1.Open dispenser door.

2.Remove all product containers and place them in a refrigerated (35-40 degrees F [1.6-4.4 degrees C]) environment. Disconnect all connections to ambient products from the bottle adapter.

3.Close the dispenser door and dispense product at each station until the product runs clear.

4.Remove the drip tray assembly and splash panel from the dispenser.

5.Replace the drip tray assembly.

6.Turn the Main Water valve to the 6 o’clock position.

7.Open the dispenser door and remove the product shelf.

8.Remove the DISPENSE/RINSE knobs Fig 7, all dispense nozzles, the 2 screws securing the cover to the dispense platform, and the cover.

9.Disconnect the dispense platform’s water lines from the supply lines inside the refrigerated cabinet and disconnect the wiring connections from the cabinet receptacles.

10.Remove the 2 thumb-screws securing the dispense platform to the cabinet .

11.Slowly pull the dispense platform forward to allow access to the rear wiring harness connector.

12.Disconnect the rear wiring harness connector from its receptacle.

13.Pull the dispense platform completely out of the cabinet and place it on a flat work surface.

14.Close the dispenser door.

15.Remove the screw securing the tubing retainer plate to the pump body and set it and the tubing retainer plate aside.

16.Gently pull the socket head screw from its notch in the pump body, releasing the spring tension on the pump band.

17.Gently pull the pump tube from around the pump’s rotor.

18.Inspect the pump band for signs of wear. Replace if necessary.

19.Release the clamps securing the old pump tubing to the plastic elbows.

20.Pull the plastic elbows from the old pump tubing, and discard the old pump tubing.

21.Insert the plastic elbows into the new pump tubing and secure it with the clamps.

22.Apply lubricant (BUNN-O-MATIC part number M2548.0000) to the new pump tubing’s rotor side.

23.Gently wrap the new pump tubing around the pump’s rotor, making sure that the elbows and clamps end up on the top-side of the pump body and don’t protrude through the exit slots.

24.Replace the socket-head screw into its notch in the pump body.

25.Replace the tubing retainer plate and its retaining screw.

26.Repeat steps 15 through 24 for the remaining pumps.

27.Replace the dispense platform into the refrigerated cabinet, making sure to reconnect all electrical and water connections.

28.Turn the Main Water Valve to the 3 o’clock position. Check for leaks.

29.Replace the thumb-screws, cover, cover screws, DISPENSE/RINSE knobs and dispense nozzles.

30.Turn all DISPENSE/RINSE knobs to the RINSE positions. Close the door and run a rinse at each station. Check for leaks.

31.Replace product shelf and product containers. Reconnect any connections to ambient product containers.

32.Prime the pumps as described in “PRIMING” in the Initial Fill Section.

13

33496 030901

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisWarranty ContentsCharge User NoticesElectrical Requirements Initial SET-UPElectrical HOOK-UP Plumbing Hookup Plumbing RequirementsSanitize Switch Refrigeration SwitchOperating Controls Water Bath and Main Water ValvesOperating Controls Loading Initial FillFrozen Concentrates Priming Initial Fill Ambient Concentrates OptionalPress and Hold Models Refer to Fig Dispenser USEPortion Control Models Refer to Fig Daily Parts Washing Cleaning & Preventive MaintenanceWeekly Sanitizing Cleaning Annually Replace Pump Tubing Cleaning Monthly Clean Condenser Air FilterSetting the MIX RATIO/BRIX Adjustment & Optional SettingsTemperature Compensated Refractometer Method Ratio Cup MethodProduct Brix % Mix RatioPump Speed Programming Chilled Water Flow Testing and Adjustment Adjustment & Optional SettingsCup Size Programming Portion Control Dispensers Only Dispenser LockoutService Lockout Adjustment & Optional Settings Password Protection Cooling Coolant Schematic Diagram Schematic Wiring Diagram

FCD-4 specifications

The Bunn FCD-4 is a commercial coffee dispenser designed to meet the demands of busy environments such as cafes, restaurants, and catering businesses. Known for its durability and performance, the FCD-4 has become a popular choice among coffee service operators.

One of the main features of the Bunn FCD-4 is its ability to hold and dispense up to four different flavors of coffee, allowing businesses to cater to diverse customer preferences. This multifunctionality is critical in settings where customers appreciate variety. With its 4.0-gallon capacity, the FCD-4 is engineered to handle high-volume service while maintaining consistent temperature and fresh taste.

The FCD-4 utilizes Bunn's well-known brewing technology. It is designed with an innovative brew sequence that optimizes coffee extraction, ensuring rich flavor profiles and maximum aroma retention. This technology, coupled with its ability to brew directly into multiple containers, provides operators with versatility and efficiency in serving coffee.

Another characteristic of the FCD-4 is its easy-to-read digital display that shows the current status of the coffee dispenser, including brew levels and operational readiness. This feature enables staff to monitor the workflow seamlessly, reducing wait times for customers.

The Bunn FCD-4 also stands out because of its user-friendly design. It includes ergonomic controls for straightforward operation, making it accessible to users with varying degrees of experience. Moreover, it is equipped with a self-cleaning function that simplifies maintenance, ensuring that the dispenser remains hygienic and operational with minimal downtime.

Durability is a hallmark of Bunn products, and the FCD-4 is no exception. Constructed with high-quality stainless steel, it is built to withstand the rigors of daily use in high-demand environments. The design also includes safety features such as automatic shut-off and temperature controls to prevent overheating, enhancing user safety.

In summary, the Bunn FCD-4 is a versatile and robust coffee dispenser that caters to the needs of commercial environments. Its capacity to hold multiple coffee flavors, advanced brewing technology, user-friendly controls, and durable construction make it a top choice for businesses aiming to deliver high-quality coffee consistently. Whether serving coffee at a busy café or during a large event, the Bunn FCD-4 is designed to enhance the coffee-serving experience.
Top Page Image Contents