Ice-O-Matic GEM0956A/W For the Plumber, Water Inlet, Water Cooled Models, Air Cooled Models, Page

Page 13
For the Plumber

GEM0650/0956/1256 A/W

For the Plumber

Water Inlet:

●Air Cooled Models: The recommended water supply is clean, cold water. Use 3/8 inch O.D. copper tubing, connect to the 3/8 inch male flare at the back of the cabinet. Install a hand valve near the machine to control the water supply.

●Water Cooled Models: A separate 3/8 inch O.D. copper line is recommended, with a separate hand valve to control it. Connect to the 3/8 inch FPT condenser inlet at the back of the cabinet. The water pressure to all lines must always be above 20 psig, and below 80 psig.

●Water Treatment: In most areas, a water filter of some type will be useful. In areas where the water is highly concentrated with minerals, the water should be tested by a water treatment specialist, and the recommendations of the specialist regarding filtration and/or treatment should be followed.

Drains:

●Air Cooled Models: Connect a rigid drain tube to the 3⁄4 FPT drain fitting at the back of the cabinet. The drain is a gravity type, and a 1⁄4 inch per foot fall is the minimum acceptable pitch for the drain. There should be a vent at the highest point of the drain line, and the ideal drain receptacle would be a trapped and vented floor drain. Use only 3⁄4 inch rigid tubing.

●Water Cooled Models: Connect a separate drain line to the 1⁄2 inch condenser drain connection at the back of the cabinet. Do not vent this drain.

●Storage Bin: Connect a separate gravity type drain line to the ice storage bin drain. Vent this drain if there is a long horizontal run from the bin to the floor drain. Insulation of this drain line is recommended.

WATER COOLED MODELS

 

 

 

 

 

 

 

 

 

AIR COOLED MODELS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Condenser Inlet

 

 

 

 

 

 

 

 

 

 

 

Water Filter

 

 

 

 

 

 

 

 

 

 

 

Water Filter

 

 

 

Vented Drain

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vented Drain

Hand Valve

Hand Valve

Condenser Drain

Water In

Vented Drain

 

Vented Drain

 

 

 

Condenser Inlet

Water InletWater Inlet:

Water In

Condenser Drain WATER COOLED MODELS

Bin Drain

Bin Drain

Floor Drain

Page 7

Image 13
Contents GEM0650A/W,GEM0956A/W and GEM1256A/W SERVICE AND INSTALLATION MANUALGEM0655 Air Page Forward GEM0650/0956/1256 A/WKeep this manual for future reference PageTable of Contents Table Of ContentsInspect Promptly Freight Claim ProcedureVisible Loss or Damage Concealed Loss or DamageICE-O-Matic WarrantyLimitation of Warranty Filing a ClaimInstallation Guidelines For the InstallerElectrical Specifications AdjustmentsGEM0650/0655/0956A/W For The InstallerGEM1256A/W Bin Application Ice Machine SpecificationsStorage Bin LocationIce machine Water LimitationsGEM 0650/0956/1256 A/W Water Inlet For the PlumberWATER COOLED MODELS AIR COOLED MODELSElectrical Connections For the ElectricianWater Cooled Models Air Cooled ModelsFinal Check List GEM0650/0956/1256A/WPre-StartInspection Start UpStart Up Air Cooled Model Shown Component DescriptionGEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider AugerElectrical Sequence To ResetElectrical Sequence Shut DownWater System Operation WaterLow Pressure Cut Out- Automatic Reset High Pressure Cut Out- Automatic ResetOperation: Performance Typical Low Side PressureICE MAKING SYSTEM: In place cleaning Sanitizing and Cleaningscheduled at a minimum of twice a year KEEP OUT OF THE REACH OF CHILDRENBearing Maintenance Bearing MaintenanceNote Left Hand Threads Bin Control Sensor Sensor MaintenanceWater Sensor Clean the air cooled condenser Maintenance Air CooledGEM0956 GEM06501. Disconnect electrical power to the ice machine Auger MaintenanceAuger 2. Turn off the water supply to the ice machineSymptom Service DiagnosisPossible Cause Probable CorrectionSymptom 4.High pressure cut out check Control System DiagnosticsWater Reservoir R&R- Water Reservoir, Bin ControlBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing AssemblyTo Remove the Auger R&R-AugerTo Remove the Water Seal R&R-WaterSealRemoval of the Water Seal To Replace the Water SealTo Replace the Evaporator R&R-EvaporatorTo Reassemble the Evaporator and Auger R&R-GearMotor To Remove and Repair the Gear Motor AssemblyTo Check the Gear Motor To Inspect the Gear MotorR&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration ServiceWiring Diagram GEM0650 A/W GEM0650 Wiring DiagramWiring Diagram GEM0956 A/W GEM0956 Wiring DiagramWiring Diagram GEM1256 A/W GEM1256 Wiring DiagramWiring Diagram GEM0655 Air GEM0655 Wiring DiagramWhat to Do Before Calling for Service Service History