Ice-O-Matic GEM0956A/W, GEM1256A/W, GEM0650A/W R&R-FanBlade and Motor, GEM0650/0956/1256 A/W, Page

Page 37

GEM0650/0956/1256 A/W

R&R-Fan Blade and Motor

To Remove the Condenser Fan Motor Assembly: (GEM0956 Shown)

1. Disconnect electrical power to the ice machine

2. Remove top panel and the service panels.

3. Unplug the fan motor wire leadsfrom the fan motors.

4. Remove the two (2)head bolt from the top end of the fan motor assembly. (Fig 1)

5. Lift up the fan motors and bracket assembly about 1⁄2 inch and pull out the fan assembly out the right service access hole. (Fig 2)

6. Repair as needed.

7. To Reassemble: Place the fan motor assembly lower flange holes over the two Allen head cap screws in the base, and install the hex head boltsat the top of the assembly. Plug the fan motors back in and replace the panels.

Fig.1

Fig. 2

Page 31

Image 37

Contents GEM0650A/W,GEM0956A/W and GEM1256A/W SERVICE AND INSTALLATION MANUALGEM0655 Air Page Forward GEM0650/0956/1256 A/WKeep this manual for future reference PageTable of Contents Table Of ContentsInspect Promptly Freight Claim ProcedureVisible Loss or Damage Concealed Loss or DamageICE-O-Matic WarrantyLimitation of Warranty Filing a ClaimInstallation Guidelines For the InstallerElectrical Specifications AdjustmentsGEM0650/0655/0956A/W For The InstallerGEM1256A/W Bin Application Ice Machine SpecificationsStorage Bin LocationIce machine Water LimitationsGEM 0650/0956/1256 A/W Water Inlet For the PlumberWATER COOLED MODELS AIR COOLED MODELSElectrical Connections For the ElectricianWater Cooled Models Air Cooled ModelsFinal Check List GEM0650/0956/1256A/WPre-StartInspection Start UpStart Up Air Cooled Model Shown Component DescriptionGEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider AugerElectrical Sequence To ResetElectrical Sequence Shut DownWater System Operation WaterLow Pressure Cut Out- Automatic Reset High Pressure Cut Out- Automatic ResetOperation: Performance Typical Low Side PressureICE MAKING SYSTEM: In place cleaning Sanitizing and Cleaningscheduled at a minimum of twice a year KEEP OUT OF THE REACH OF CHILDRENBearing Maintenance Bearing MaintenanceNote Left Hand Threads Bin Control Sensor Sensor MaintenanceWater Sensor Clean the air cooled condenser Maintenance Air CooledGEM0956 GEM06501. Disconnect electrical power to the ice machine Auger MaintenanceAuger 2. Turn off the water supply to the ice machineSymptom Service DiagnosisPossible Cause Probable CorrectionSymptom 4.High pressure cut out check Control System DiagnosticsWater Reservoir R&R- Water Reservoir, Bin ControlBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing AssemblyTo Remove the Auger R&R-AugerTo Remove the Water Seal R&R-WaterSealRemoval of the Water Seal To Replace the Water SealTo Replace the Evaporator R&R-EvaporatorTo Reassemble the Evaporator and Auger R&R-GearMotor To Remove and Repair the Gear Motor AssemblyTo Check the Gear Motor To Inspect the Gear MotorR&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration ServiceWiring Diagram GEM0650 A/W GEM0650 Wiring DiagramWiring Diagram GEM0956 A/W GEM0956 Wiring DiagramWiring Diagram GEM1256 A/W GEM1256 Wiring DiagramWiring Diagram GEM0655 Air GEM0655 Wiring DiagramWhat to Do Before Calling for Service Service History