Ice-O-Matic GEM0650A/W GEM0650/0956/1256A/W, Final Check List, For the Installer, Page

Page 15
GEM0650/0956/1256A/W

GEM0650/0956/1256A/W

For the Installer

Final Check List:

 

 

 

 

 

_______1.

Is the ice machine installed indoors in a location where the air and water temperatures are

 

 

 

 

 

 

 

 

 

 

 

controlled and where they do not exceed the design limitations?

 

 

 

 

_____2.

Is there an electrical service disconnect within sight of the installed machine?

 

 

 

 

 

_____3.

Has the voltage been checked and compared to the nameplate requirements?

 

 

 

 

 

_____4.

Have all the plumbing connections been made and checked for leaks?

 

 

 

 

 

 

 

 

 

 

 

_____5.

Is the ice machine and storage bin level?

 

 

 

 

 

 

 

_____6.

Is there a minimum of 6 inches of clearance at the back of the machine for proper service

 

 

 

 

 

 

access and air circulation?

 

 

 

 

_____7.

Is the water pressure a minimum of 20 psig?

 

 

 

 

 

 

 

 

 

 

 

_____8.

Has the ice machine been secured to the bin?

 

 

 

 

 

 

 

_____9.

Is there clearance over the top of the ice machine for service access?

 

 

 

 

 

 

 

____10.

Is there a water shut off valve installed near the ice machine?

 

 

 

 

 

 

 

____11.

Have all the shipping blocks been removed from the ice machine?

 

 

 

 

Insure the machine is level

Note: Fasten the ice machine to the bin with the hardware supplied with the ice machine

Page 9

Image 15
Contents SERVICE AND INSTALLATION MANUAL GEM0650A/W,GEM0956A/W and GEM1256A/WGEM0655 Air Page Page GEM0650/0956/1256 A/WForward Keep this manual for future referenceTable of Contents Table Of ContentsConcealed Loss or Damage Freight Claim ProcedureInspect Promptly Visible Loss or DamageFiling a Claim WarrantyICE-O-Matic Limitation of WarrantyAdjustments For the InstallerInstallation Guidelines Electrical SpecificationsGEM0650/0655/0956A/W For The InstallerGEM1256A/W Bin Application Ice Machine SpecificationsWater Limitations LocationStorage Bin Ice machineGEM 0650/0956/1256 A/W AIR COOLED MODELS For the PlumberWater Inlet WATER COOLED MODELSAir Cooled Models For the ElectricianElectrical Connections Water Cooled ModelsFinal Check List GEM0650/0956/1256A/WStart Up Pre-StartInspectionStart Up Air Cooled Model Shown Component DescriptionGEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider AugerShut Down To ResetElectrical Sequence Electrical SequenceWater System Operation WaterTypical Low Side Pressure High Pressure Cut Out- Automatic ResetLow Pressure Cut Out- Automatic Reset Operation: PerformanceKEEP OUT OF THE REACH OF CHILDREN Sanitizing and CleaningICE MAKING SYSTEM: In place cleaning scheduled at a minimum of twice a yearBearing Maintenance Bearing MaintenanceNote Left Hand Threads Sensor Maintenance Bin Control SensorWater Sensor GEM0650 Maintenance Air CooledClean the air cooled condenser GEM09562. Turn off the water supply to the ice machine Auger Maintenance1. Disconnect electrical power to the ice machine AugerProbable Correction Service DiagnosisSymptom Possible CausePossible Cause 4.High pressure cut out check Control System DiagnosticsR&R- Water Reservoir, Bin Control Water ReservoirBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing AssemblyTo Remove the Auger R&R-AugerTo Replace the Water Seal R&R-WaterSealTo Remove the Water Seal Removal of the Water SealR&R-Evaporator To Replace the EvaporatorTo Reassemble the Evaporator and Auger To Inspect the Gear Motor To Remove and Repair the Gear Motor AssemblyR&R-GearMotor To Check the Gear MotorR&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration ServiceWiring Diagram GEM0650 A/W GEM0650 Wiring DiagramWiring Diagram GEM0956 A/W GEM0956 Wiring DiagramWiring Diagram GEM1256 A/W GEM1256 Wiring DiagramWiring Diagram GEM0655 Air GEM0655 Wiring DiagramWhat to Do Before Calling for Service Service History