Electrical Connections and Motor Specifications for Your Saw | Essential Safety Tips

Electrical Connections

Motor Specifications

The AC motor used on this saw is a capaci- tor-start, non-reversible type. The model covered in this manual has the following specifications:

Specification:	Model
	RS10000
Rated H.P.	1.5
Max Developed H.P.	3.0
Voltage	120/240
Amperes	13/6.5
Hertz (cycles)	60
Phase	single
RPM	3450
Arbor Shaft Rotation	Clockwise
Run Capacitor	Yes

Note: If saw does not start when switched on, imme- diately turn saw off and refer to Troubleshooting. Leaving the switch on will destroy the motor

Power Supply

WARNING

Saw is factory wired for 120V opera- tion. Connect to 120V, 15-AMP branch circuit and use 15-AMP time delay fuse or circuit breaker. Failure to connect in this way could result in injury from shock or fire.

The saw must be properly grounded. Not all outlets are properly grounded. If you are not sure that your outlet is properly grounded, have it checked by a qualified electrician.

WARNING

If not properly grounded, this power tool could cause electrical shock, par- ticularly when used in damp locations.

WARNING

If electrical shock occurs, your reac- tion to shock could bring hands into contact with blade.

WARNING

To avoid electric shock or fire, immedi- ately replace worn, cut, or damaged power cord.

The unit is wired for 120V and has a plug that looks like this:

3-Prong Plug

Grounding

Prong

Properly

Grounded Outlet

The power tool is equipped with a 3-conduc- tor cord and grounding type plug listed by Underwriters' Laboratories. The ground con- ductor has a green jacket and is attached to the tool housing at one end and to the ground prong in the attachment plug at the other end.

The plug requires a mating 3-conductor grounded type outlet as shown above. If you have an outlet that is of the 2-prong type, it is recommended that you have a qualified electrician replace it with a properly grounded 3-prong outlet.

42

Image 42

RIDGID SP6263 manual Electrical Connections, Motor Specifications

Contents

RS1000 Table of Contents Read and follow all safety information and instructions SafetySafety Symbol and Signal Words Major Hazards Kickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Arsenic and chromium from chemi- cally-treated lumber Saw Safety Instructions Workpiece Safety Instructions Blade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label Introduction AssemblyIdentify Parts This model includes 16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Mounting Saw Attach Elevation CrankElevate arm approximately 3 to 4 Inches Install arm cap Make certain power cord is unplugged Attaching Carriage Motor to ArmLock miter/arm lock before proceeding Remove saw blade Attach Table Supports Adjustments Yoke Clamp Adjustment Bevel Lock Lever Arm to Column Adjustment Adjusting Column Tube in Column SupportAlignment Checks Alignment Adjustments Adjusting Carriage Bearings Lock Lnstalling Front Table Five Counterbored Holes Top Bottom Channel Clip Make Front Table Flat To lower center, tighten center 1-3/4 long pan head screw Square Crosscut Travel Alignment and Adjustment StepsAlignment Squaring cross cut travel Alignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Align Riving Knife to Blade Raise riving knife and tighten pawls/riving knife knob Controls Bevel index lever must be unindexed before moving motor Yoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Motor Specifications Electrical Connections Motor Protection & Reset Button Extension Cords To Change Motor Voltage to 240 Volt A.C Crosscutting Safety CrosscuttingCrosscutting Defined Crosscut Kerfs Keep one hand on saw handle through step Making Crosscuts Repetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed Directions Ripping Kickback To reduce risk of kickback Tial barrier to outfeed side Hold Down Function Pawls and Riving Knife Function Ripping Set-up Procedure Follow these steps before ripping Making Rip Cuts Keep Hand Dado Blades, Molding Heads EdgingRipping Hints Cutting Aides Making the Handle Putting it togetherAuxiliary Fence Molding/Sanding Featherboard Cutting Aids H.A. Requirements Accessories Accessories SafetyInformation for Edging Maintenance General InformationLubrication Replacing Pawls Lubricating Blade Guard AssemblyAdjusting the Trigger Blade Changing Troubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Saw Problem Possible Causes What to DoPage Repair Repair Parts Always order by Part Number Not by Key Number Repair Yoke Assembly Parts 44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What we will do to correct problems What is coveredHow can you get service What is not covered