Tools Needed for Assembly and Alignment | RIDGID SP6263 guide

Assembly

Crank

1/4" Diam. x 5/8" Long Truss Head Screw (24)

Leveling Foot (4)

3/8" Diam. Hex Nut (8)

5/16" Diam. Hex Nut (4)

1/4" Diam. Hex Nut (24)

Arm Cap

1/4" External Tooth

Lockwasher (24)

5/16" Diam. External Lockwasher (4)

11/32" x 11/16" x 1/16" Washer (8)

5/16" Diam. x 5/8" Long Hex Head Screw (4)

Tools Needed for Assembly and Alignment

7/16-inch Wrench
1/2-inch Wrench	Medium Screwdriver

9/16-inch Wrench	1/8" Hex Wrench
	1/8" Hex Wrench
5/8-inch Wrench		Phillips Screwdriver
5/8-inch Wrench
15/16-inch Wrench

Pliers

Small Hammer

Pencil

Framing Square

14

Image 14

RIDGID SP6263 manual Tools Needed for Assembly and Alignment

Contents

RS1000 Table of Contents Read and follow all safety information and instructions SafetySafety Symbol and Signal Words Major Hazards Kickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Arsenic and chromium from chemi- cally-treated lumber Saw Safety Instructions Workpiece Safety Instructions Blade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label Introduction AssemblyIdentify Parts This model includes 16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Elevate arm approximately 3 to 4 Inches Mounting SawAttach Elevation Crank Lock miter/arm lock before proceeding Install arm cap Make certain power cord is unpluggedAttaching Carriage Motor to Arm Remove saw blade Attach Table Supports Adjustments Yoke Clamp Adjustment Bevel Lock Lever Alignment Checks Arm to Column AdjustmentAdjusting Column Tube in Column Support Alignment Adjustments Adjusting Carriage Bearings Lock Lnstalling Front Table Five Counterbored Holes Top Bottom Channel Clip Make Front Table Flat To lower center, tighten center 1-3/4 long pan head screw Square Crosscut Travel Alignment and Adjustment StepsAlignment Squaring cross cut travel Alignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Align Riving Knife to Blade Raise riving knife and tighten pawls/riving knife knob Controls Bevel index lever must be unindexed before moving motor Yoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Motor Specifications Electrical Connections Motor Protection & Reset Button Extension Cords To Change Motor Voltage to 240 Volt A.C Crosscutting Defined Crosscutting SafetyCrosscutting Crosscut Kerfs Keep one hand on saw handle through step Making Crosscuts Repetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed Directions Ripping Kickback To reduce risk of kickback Tial barrier to outfeed side Hold Down Function Pawls and Riving Knife Function Ripping Set-up Procedure Follow these steps before ripping Making Rip Cuts Keep Hand Ripping Hints Dado Blades, Molding HeadsEdging Cutting Aides Auxiliary Fence Making the HandlePutting it together Molding/Sanding Featherboard Cutting Aids H.A. Requirements Information for Edging AccessoriesAccessories Safety Lubrication MaintenanceGeneral Information Replacing Pawls Lubricating Blade Guard AssemblyAdjusting the Trigger Blade Changing Troubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Saw Problem Possible Causes What to DoPage Repair Repair Parts Always order by Part Number Not by Key Number Repair Yoke Assembly Parts 44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What we will do to correct problems What is coveredHow can you get service What is not covered