Mounting Saw, Attach Elevation Crank | RIDGID SP6263 instruction

Assembly

Mounting Saw

1.From among the loose parts, find the fol- lowing hardware:

4 Hex Head Screws, 5/16-18 x 5/8

4Lockwasher, 5/16 in. External Type

8Washers, 11/32 ID

4Hex Jam Nuts, 5/16-18

2.Place saw on legs so that holes in bottom of saw line up with holes marked X in top of legs and RIDGID logo on leg set is facing front.

3.Install screws, washers and nuts as shown.

4.If you mount the saw on any other RIDGID base or flat bench, make sure Ele- vation Crank has proper clearance to rotate. The saw must be bolted down. Position saw to slope slightly rearward, so when the car- riage is installed it will not roll forward due to gravity.

Saw Base

Hex Head

Screw

Flat Washer

Stiffener

Flat Washer

Lockwasher

Hex Nut

Attach Elevation Crank.

Install crank on elevation shaft. Be sure set- screw is tightened on flat of shaft.

Elevate arm approximately 3 to 4 Inches.

Remove shipping block and discard.

Leg

Leg

Side

Stiffener

Front Stiffener

WARNING

Saw must slant slightly towards rear to keep blade carriage from rolling for- ward. Workpiece or saw can move unexpectedly if leg set rocks. Fingers, hand or arm could be cut off by blade contact. Adjust leveling feet before using saw.

Shipping Block

Elevation Crank (Turn clockwise to raise arm)

16

Image 16

RIDGID SP6263 manual Mounting Saw, Attach Elevation Crank, Elevate arm approximately 3 to 4 Inches

Contents

RS1000 Table of Contents Safety Safety Symbol and Signal WordsRead and follow all safety information and instructions Major Hazards Kickback Hazard Guard Function and Features Hazards Associated with Clear Por- tion of Guard Safety Instructions Personal Safety InstructionsWork Area Safety Instructions Arsenic and chromium from chemi- cally-treated lumber Saw Safety Instructions Workpiece Safety Instructions Blade Safety Instructions On-Product Safety Labels On the clear plastic guard is this Osha required label Assembly Identify PartsIntroduction This model includes 16-18 x 3/4 Long Diam. Hex Nut Tools Needed for Assembly and Alignment Assembling steel legs Attach Elevation Crank Mounting SawElevate arm approximately 3 to 4 Inches Attaching Carriage Motor to Arm Install arm cap Make certain power cord is unpluggedLock miter/arm lock before proceeding Remove saw blade Attach Table Supports Adjustments Yoke Clamp Adjustment Bevel Lock Lever Adjusting Column Tube in Column Support Arm to Column AdjustmentAlignment Checks Alignment Adjustments Adjusting Carriage Bearings Lock Lnstalling Front Table Five Counterbored Holes Top Bottom Channel Clip Make Front Table Flat To lower center, tighten center 1-3/4 long pan head screw Alignment and Adjustment Steps AlignmentSquare Crosscut Travel Squaring cross cut travel Alignment Front Table Fence Square Blade to Table for Crosscutting Square Blade to Fence Make Blade Parallel to Table Lnstalling and Adjusting Rip Scale Indica- tors Install Guard Align Riving Knife to Blade Raise riving knife and tighten pawls/riving knife knob Controls Bevel index lever must be unindexed before moving motor Yoke Index Lever Table Clamp Elevation Crank Always Lock before ripping Controls Pawls/Riving Knife Knob Guard Tab Motor Specifications Electrical Connections Motor Protection & Reset Button Extension Cords To Change Motor Voltage to 240 Volt A.C Crosscutting Crosscutting SafetyCrosscutting Defined Crosscut Kerfs Keep one hand on saw handle through step Making Crosscuts Repetitive Crosscutting Ripping Ripping DefinedIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Ripping Kickback To reduce risk of kickback Tial barrier to outfeed side Hold Down Function Pawls and Riving Knife Function Ripping Set-up Procedure Follow these steps before ripping Making Rip Cuts Keep Hand Edging Dado Blades, Molding HeadsRipping Hints Cutting Aides Putting it together Making the HandleAuxiliary Fence Molding/Sanding Featherboard Cutting Aids H.A. Requirements Accessories Safety AccessoriesInformation for Edging General Information MaintenanceLubrication Lubricating Blade Guard Assembly Adjusting the TriggerReplacing Pawls Blade Changing Troubleshooting Motor Problem Possible Causes What to Do Cutting Problem Possible Causes What to Do Saw Problem Possible Causes What to DoPage Repair Repair Parts Always order by Part Number Not by Key Number Repair Yoke Assembly Parts 44 45 Standard Hardware Item May Be Purchased Locally Location of Lower Guard Guard Parts List for Ridgid 10 Radial SAW Leg Set Always order by Part Number Not by Key Number What is covered How can you get serviceWhat we will do to correct problems What is not covered