Ice-O-Matic GEM0655 Air For the Electrician, Electrical Connections, Water Cooled Models, Page

Page 14

GEM0650/0956/1256 A/W

For the Electrician

Electrical Connections:

Check the ice machine nameplate (located on the back panel) for the voltage requirements, and minimum circuit ampacity. The ice machine requires a solid chassis to earth ground.

Connect the ice machine to its own electrical circuit so it is individually fused. Voltage variation must remain within the limitations, even under starting conditions.

Note: All external wiring must conform to national, state and local electrical codes. The use of a licensed electrician is required to perform the electrical installation.

Water Cooled Models		Power
		Supply

Electrical Inlet

Air Cooled Models

Page 8

Image 14

Contents GEM0655 Air SERVICE AND INSTALLATION MANUALGEM0650A/W,GEM0956A/W and GEM1256A/W Page Keep this manual for future reference GEM0650/0956/1256 A/WForward PageTable Of Contents Table of ContentsVisible Loss or Damage Freight Claim ProcedureInspect Promptly Concealed Loss or DamageLimitation of Warranty WarrantyICE-O-Matic Filing a ClaimElectrical Specifications For the InstallerInstallation Guidelines AdjustmentsFor The Installer GEM0650/0655/0956A/WGEM1256A/W Ice Machine Specifications Bin ApplicationIce machine LocationStorage Bin Water LimitationsGEM 0650/0956/1256 A/W WATER COOLED MODELS For the PlumberWater Inlet AIR COOLED MODELSWater Cooled Models For the ElectricianElectrical Connections Air Cooled ModelsGEM0650/0956/1256A/W Final Check ListStart Up Start UpPre-StartInspection Component Description Air Cooled Model ShownGEM0650/0956/1256 A/W Component Description Ice Sweep Bearing Breaker/Divider Auger Evaporator Motor Water SealElectrical Sequence To ResetElectrical Sequence Shut DownOperation Water Water SystemOperation: Performance High Pressure Cut Out- Automatic ResetLow Pressure Cut Out- Automatic Reset Typical Low Side Pressurescheduled at a minimum of twice a year Sanitizing and CleaningICE MAKING SYSTEM: In place cleaning KEEP OUT OF THE REACH OF CHILDRENNote Left Hand Threads Bearing MaintenanceBearing Maintenance Water Sensor Sensor MaintenanceBin Control Sensor GEM0956 Maintenance Air CooledClean the air cooled condenser GEM0650Auger Auger Maintenance1. Disconnect electrical power to the ice machine 2. Turn off the water supply to the ice machinePossible Cause Service DiagnosisSymptom Probable CorrectionGEM0650/0956/1256 A/W Control System Diagnostics 4.High pressure cut out checkBin Controls Ice Level Sensors R&R- Water Reservoir, Bin ControlWater Reservoir To Remove the Breaker Bearing Assembly R&R-Bearingand BreakerR&R-Auger To Remove the AugerRemoval of the Water Seal R&R-WaterSealTo Remove the Water Seal To Replace the Water SealTo Reassemble the Evaporator and Auger R&R-EvaporatorTo Replace the Evaporator To Check the Gear Motor To Remove and Repair the Gear Motor AssemblyR&R-GearMotor To Inspect the Gear MotorR&R-FanBlade and Motor Refrigeration Service Instructions for Liquid Charging R404AGEM0650 Wiring Diagram Wiring Diagram GEM0650 A/WGEM0956 Wiring Diagram Wiring Diagram GEM0956 A/WGEM1256 Wiring Diagram Wiring Diagram GEM1256 A/WGEM0655 Wiring Diagram Wiring Diagram GEM0655 AirService History What to Do Before Calling for Service