Ice-O-Matic GEM0650A/W, GEM1256A/W, GEM0956A/W GEM0650/0956/1256 A/W, Component Description, Page

Page 19
Ice Sweep

GEM0650/0956/1256 A/W

Component Description

●Evaporator: A refrigerated vertical tube filled with water and containing a water seal and auger.

●Auger: A solid stainless steel double spiral auger, it pushes the ice crystals up to the top of the evaporator.

●Water Seal: A two part “face” seal, the top half rotating with the auger, the bottom half stationary, the sealing action being where the two “faces” meet.

●Ice Sweep: A plastic cap with “fingers”. It revolves with the auger to “sweep” the ice into the ice chute.

●Breaker (Divider): Where the ice is compressed and much of the extra water is squeezed out of it before it is discharged into the bin.

●Motor: A split phase motor that drives the gear reducer.

●Thrust Bearings: As the ice is pushed up the evaporator, the auger is thrust down, and pressure from the auger thrust is taken up by this bearing.

Ice Sweep

Bearing

Breaker/Divider

Auger

Evaporator

Motor

Water Seal

Page 13

Image 19
Contents GEM0650A/W,GEM0956A/W and GEM1256A/W SERVICE AND INSTALLATION MANUALGEM0655 Air Page Page GEM0650/0956/1256 A/WForward Keep this manual for future referenceTable of Contents Table Of ContentsConcealed Loss or Damage Freight Claim ProcedureInspect Promptly Visible Loss or DamageFiling a Claim WarrantyICE-O-Matic Limitation of WarrantyAdjustments For the InstallerInstallation Guidelines Electrical SpecificationsGEM0650/0655/0956A/W For The InstallerGEM1256A/W Bin Application Ice Machine SpecificationsWater Limitations LocationStorage Bin Ice machineGEM 0650/0956/1256 A/W AIR COOLED MODELS For the PlumberWater Inlet WATER COOLED MODELSAir Cooled Models For the ElectricianElectrical Connections Water Cooled ModelsFinal Check List GEM0650/0956/1256A/WPre-StartInspection Start UpStart Up Air Cooled Model Shown Component DescriptionGEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider AugerShut Down To ResetElectrical Sequence Electrical SequenceWater System Operation WaterTypical Low Side Pressure High Pressure Cut Out- Automatic ResetLow Pressure Cut Out- Automatic Reset Operation: PerformanceKEEP OUT OF THE REACH OF CHILDREN Sanitizing and CleaningICE MAKING SYSTEM: In place cleaning scheduled at a minimum of twice a yearBearing Maintenance Bearing MaintenanceNote Left Hand Threads Bin Control Sensor Sensor MaintenanceWater Sensor GEM0650 Maintenance Air CooledClean the air cooled condenser GEM09562. Turn off the water supply to the ice machine Auger Maintenance1. Disconnect electrical power to the ice machine AugerProbable Correction Service DiagnosisSymptom Possible CausePossible Cause 4.High pressure cut out check Control System DiagnosticsWater Reservoir R&R- Water Reservoir, Bin ControlBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing AssemblyTo Remove the Auger R&R-AugerTo Replace the Water Seal R&R-WaterSealTo Remove the Water Seal Removal of the Water SealTo Replace the Evaporator R&R-EvaporatorTo Reassemble the Evaporator and Auger To Inspect the Gear Motor To Remove and Repair the Gear Motor AssemblyR&R-GearMotor To Check the Gear MotorR&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration ServiceWiring Diagram GEM0650 A/W GEM0650 Wiring DiagramWiring Diagram GEM0956 A/W GEM0956 Wiring DiagramWiring Diagram GEM1256 A/W GEM1256 Wiring DiagramWiring Diagram GEM0655 Air GEM0655 Wiring DiagramWhat to Do Before Calling for Service Service History