Ice-O-Matic GEM0650A/W R&R- Water Reservoir, Bin Control, Bin Controls Ice Level Sensors, Page

Page 31
R&R- Water Reservoir, Bin Control

GEM0650/0956/1256 A/W

R&R- Water Reservoir, Bin Control

Water Reservoir:

1.Disconnect electrical power supply.

2.Shut off water supply to the ice maker.

3.Remove the front panel.

4.Disconnect water inlet tube from reservoir inlet fitting.

5.To remove float valve, push in “locking tabs” as shown and pull float up. Note: The plunger/seat is available separately as a part.

6.To remove reservoir, pull up and remove water sensor.

7.Disconnect water outlet tubes.

8.Remove mounting screws from reservoir bracket, and remove reservoir from ice maker.

9.Reverse to reassemble.

Float Assembly

Locking Tabs

Ice Chute

Slide Bin

Controls to

Remove

Water

Sensor

Bin Controls (Ice Level Sensors)

1.Disconnect electrical power supply.

2.Remove the front panel.

3.Remove the control box cover.

4.Locate ice chute, at the base of the chute, in front of and behind it are two plastic bin control mounts.

5.Slide each bin control to the left, and disconnect the electrical leads connecting the bin control to the circuit board.

6.Reverse to reassemble, be certain that the bin controls are aligned so that the ice level sensors are visible (centered) through the holes in the ice chute.

Page 25

Image 31
Contents GEM0650A/W,GEM0956A/W and GEM1256A/W SERVICE AND INSTALLATION MANUALGEM0655 Air Page Page GEM0650/0956/1256 A/WForward Keep this manual for future referenceTable of Contents Table Of ContentsConcealed Loss or Damage Freight Claim ProcedureInspect Promptly Visible Loss or DamageFiling a Claim WarrantyICE-O-Matic Limitation of WarrantyAdjustments For the InstallerInstallation Guidelines Electrical SpecificationsGEM0650/0655/0956A/W For The InstallerGEM1256A/W Bin Application Ice Machine SpecificationsWater Limitations LocationStorage Bin Ice machineGEM 0650/0956/1256 A/W AIR COOLED MODELS For the PlumberWater Inlet WATER COOLED MODELSAir Cooled Models For the ElectricianElectrical Connections Water Cooled ModelsFinal Check List GEM0650/0956/1256A/WPre-StartInspection Start UpStart Up Air Cooled Model Shown Component DescriptionGEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider AugerShut Down To ResetElectrical Sequence Electrical SequenceWater System Operation WaterTypical Low Side Pressure High Pressure Cut Out- Automatic ResetLow Pressure Cut Out- Automatic Reset Operation: PerformanceKEEP OUT OF THE REACH OF CHILDREN Sanitizing and CleaningICE MAKING SYSTEM: In place cleaning scheduled at a minimum of twice a yearBearing Maintenance Bearing MaintenanceNote Left Hand Threads Bin Control Sensor Sensor MaintenanceWater Sensor GEM0650 Maintenance Air CooledClean the air cooled condenser GEM09562. Turn off the water supply to the ice machine Auger Maintenance1. Disconnect electrical power to the ice machine AugerProbable Correction Service DiagnosisSymptom Possible CausePossible Cause 4.High pressure cut out check Control System DiagnosticsWater Reservoir R&R- Water Reservoir, Bin ControlBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing AssemblyTo Remove the Auger R&R-AugerTo Replace the Water Seal R&R-WaterSealTo Remove the Water Seal Removal of the Water SealTo Replace the Evaporator R&R-EvaporatorTo Reassemble the Evaporator and Auger To Inspect the Gear Motor To Remove and Repair the Gear Motor AssemblyR&R-GearMotor To Check the Gear MotorR&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration ServiceWiring Diagram GEM0650 A/W GEM0650 Wiring DiagramWiring Diagram GEM0956 A/W GEM0956 Wiring DiagramWiring Diagram GEM1256 A/W GEM1256 Wiring DiagramWiring Diagram GEM0655 Air GEM0655 Wiring DiagramWhat to Do Before Calling for Service Service History