Ice-O-Matic GEM0956A/W, GEM1256A/W Sensor Maintenance, Bin Control Sensor, Water Sensor, Page

Page 25
Sensor Maintenance

GEM0650/0956/1256 A/W

Sensor Maintenance

Bin Control Sensor:

The bin control uses devices that sense light, therefore they must be kept clean enough so that they can “see”.

At least twice a year, remove the bin control sensors from the base of the chute, and wipe the inside clean, as illustrated.

Slide Bin Controls to

Remove

Water Sensor:

The ice machine uses a probe in the water reservoir to determine if there is water.

At least twice a year remove the probe from the reservoir and wipe the tip clean of mineral build-up.

 

Clean the probe’s tip with ice

 

machine cleaner and a soft

Page 19

cloth.

Image 25
Contents GEM0650A/W,GEM0956A/W and GEM1256A/W SERVICE AND INSTALLATION MANUALGEM0655 Air Page Forward GEM0650/0956/1256 A/WKeep this manual for future reference PageTable of Contents Table Of ContentsInspect Promptly Freight Claim ProcedureVisible Loss or Damage Concealed Loss or DamageICE-O-Matic WarrantyLimitation of Warranty Filing a ClaimInstallation Guidelines For the InstallerElectrical Specifications AdjustmentsGEM0650/0655/0956A/W For The InstallerGEM1256A/W Bin Application Ice Machine SpecificationsStorage Bin LocationIce machine Water LimitationsGEM 0650/0956/1256 A/W Water Inlet For the PlumberWATER COOLED MODELS AIR COOLED MODELSElectrical Connections For the ElectricianWater Cooled Models Air Cooled ModelsFinal Check List GEM0650/0956/1256A/WPre-StartInspection Start UpStart Up Air Cooled Model Shown Component DescriptionGEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider AugerElectrical Sequence To ResetElectrical Sequence Shut DownWater System Operation WaterLow Pressure Cut Out- Automatic Reset High Pressure Cut Out- Automatic ResetOperation: Performance Typical Low Side PressureICE MAKING SYSTEM: In place cleaning Sanitizing and Cleaningscheduled at a minimum of twice a year KEEP OUT OF THE REACH OF CHILDRENBearing Maintenance Bearing MaintenanceNote Left Hand Threads Bin Control Sensor Sensor MaintenanceWater Sensor Clean the air cooled condenser Maintenance Air CooledGEM0956 GEM06501. Disconnect electrical power to the ice machine Auger MaintenanceAuger 2. Turn off the water supply to the ice machineSymptom Service DiagnosisPossible Cause Probable CorrectionSymptom 4.High pressure cut out check Control System DiagnosticsWater Reservoir R&R- Water Reservoir, Bin ControlBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing AssemblyTo Remove the Auger R&R-AugerTo Remove the Water Seal R&R-WaterSealRemoval of the Water Seal To Replace the Water SealTo Replace the Evaporator R&R-EvaporatorTo Reassemble the Evaporator and Auger R&R-GearMotor To Remove and Repair the Gear Motor AssemblyTo Check the Gear Motor To Inspect the Gear MotorR&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration ServiceWiring Diagram GEM0650 A/W GEM0650 Wiring DiagramWiring Diagram GEM0956 A/W GEM0956 Wiring DiagramWiring Diagram GEM1256 A/W GEM1256 Wiring DiagramWiring Diagram GEM0655 Air GEM0655 Wiring DiagramWhat to Do Before Calling for Service Service History