GE Monogram Range Convert the Regulator, Tools YOU Needed for Conversion, Change Burner Orifices

Page 21
Main
Orifice
Burner Orifices
Spark
Igniter

Installation Instructions

Convert Natural Gas to LP Gas Operation

Convert LP Gas to Natural Gas Operation

WARNING: This conversion must

be performed by a qualified installer or gas supplier in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion.

WARNING: The rangetop, as shipped from the factory, is set for use with its intended gas. If you wish to use your rangetop with the alternate gas, you must first replace the orifices and convert the pressure regulator.

WARNING: The following adjustments must be made before turning on the burner. Failure to do so

2 CONVERT THE REGULATOR

Disconnect all electrical power at the main circuit breaker or fuse box.

A. Remove the rear vent Range Regulator

trim (on ranges only) to access the regulator. The

Rangetop regulator is on the left bottom

corner.

B.Shut off the gas supply by closing the manual shut-offvalve in the unit or at the wall.

C.Convert the pressure regulator:

Unscrew the cap with plunger.

Place your thumb against flat side of the plunger and press down to snap the plunger out of the cap.

Carefully look at the plunger to locate the NAT or LP position.

could result in serious injury. Be sure pressure regulator has been converted as described in Step 2.

TOOLS YOU NEEDED FOR CONVERSION

Turn the plunger over so that the desired gas

is showing

NAT. Position

near the

 

bottom.

 

Cap

PL

NAT

LP

NAT

Gasket

ATN

LP

Plunger

NAT

LP

LP Position

OFF FOR

DOWN

Crescent Wrench

1/4” and 7mm Nutdrivers

 

 

Small Flat-Head Screwdriver

Safety Glasses

(2 to 2.4 mm or 3/32” tip size,

60 mm long)

 

Pressure Regulator

Snap the plunger back into the cap.

Screw the cap back onto the regulator.

3 CHANGE BURNER ORIFICES

 

 

 

 

Philips

 

1/2” Deepwell

Small Pliers

Screwdriver

 

Socket Wrench

 

 

 

1

ORIFICE HOLDER

Griddle

Grill

Orifice

Orifice

The range orifice holder

is located behind the front access panel at the bottom of the range.

The rangetop orifice holder

is located inside the range insulation cover.

Additional orifices may be present. Use only the orifices specified in the instructions for your range or rangetop.

INSTALLATION TIP: First remove all orifices and then start replacing them. This will help to prevent the possibility that some may not be replaced.

Burner

A. Remove the burner grates, Head burner caps and burner heads.

B. Loosen the top burner orifices using a 7 mm nut driver. Use small

pliers to carefully lift out the orifices.

The main orifice is located low in the center of the burner, while the simmer orifice is located higher beside the center

of the burner.

Burner Cap

Burner Base

Simmer

Orifice

21

Image 21
Contents Instrucciones de instalación Instructions d’installationVent hood Combinations Installation InstructionsCompletion Time 1 to 3 hours Read these instructions completely and carefullyBacksplash Accessories ContentsDesign Information Models AvailableRange Models Design InformationTo 4-3/4 Toekick/leg Height Minimum To Adjacent Wall Above the range and below Wide Range Models48, 36 and 30 Range Models Product Dimensions and ClearancesWB28K10553 High Altitude KIT Installation InformationWB28K10554 DE-RATE KIT Materials ProvidedPower Supply Locations Installation PreparationSee 3-wire power cord installation on the next Gas SupplyDo not remove the ground strap connection Wire Power Cord InstallationInstallation Remove PackagingTo remove the oven doors Tilt the range forward on the skid Move the Range IndoorsLift the toekick out of the foam base Tilt the range to lower the hand-truck wheels off the skidAnti-Tip Parts Provided Anti-Tip Brace Aham Anti-Tip Safety BrochureHex Screws Anti-Tip Brace Alternate Brace Position Anti-Tip BracketRoll Range Into Position Connect Range to GASConnect Electrical Assure that gas supply is turned off at the shut-off valveRear LEG Adjustment Front LEG AdjustmentLevel the Range Level the RangeInstallation Checklist Finalize InstallationCheck Burners Recheck StepsACCESSORIES-TOEKICK provided Top Toekick BottomToekick Push Install 12 Backsplash Optional ACCESSORIES-12 High BacksplashTools and Materials Required This Kit IncludesACCESSORIES-30 to 36 Adjustable Backsplash not included Install the Wall Support PanelsMaximum shelf load-bearing weight is 40 lbs Install Cover Panels Install Cover PanelsSee alternate method if side access is blocked Alternate Method When side access is blockedConvert the Regulator Tools YOU Needed for ConversionChange Burner Orifices Change Burner Orifices Installation Instructions for Gas ConversionChange Grill Orifice if present ZDP364, ZDP366, ZDP484, ZDP486Change Griddle Orifice if present Adjust Burner FlamesRemarque à l’attention de l’installateur Consignes d’installationTemps d’installation 1 à 3 heures Dispositions de hotte d’extractionTable DES Matières CaractéristiquesModèles Disponibles DosseretModèles de cuisinière 121 cm Dimensions DU Produit ET Espaces DE SéparationModèles de cuisinière 91 cm 36’’ Caractéristiques Dimensions DE L’APPAREIL ET EspacesModèles de cuisinière 76 cm 30’’ Dimensions DE L’APPAREIL ET EspacesModèles de cuisinière 76 cm 30’’, 91 cm 36’’ et 121 cm 10-1/2 24,13 cm 13/16 2 cm Dosseret 30-36 En option28-1/4 70,96 cm Jusquà lavant de la porte KIT DE Réduction DES Caractéristiques Nominales WB28K10554 KIT Haute Altitude WB28K10553Matériel Fourni Outils NécessairesEmplacement DES Alimentations Préparation de l’installationAlimentation de gaz Alimentation électriqueInstallation DU Cordon ’ALIMENTATION 4 Fils Installation DU Cordon ’ALIMENTATION 3 FilsNE retirez PAS le branchement du conducteur de terre Pour retirer lales portes Étape 1 Sortez L’APPAREIL DE SON EmballageAttaches Rainure Verrou de charnièreÉtape 2 Déplacez LA Cuisinière À L’INTÉRIEUR Soulevez la plinthe du socle en moussePlinthe Pièces du support anti-basculement fournies Vis à boisVis à tête hexagonale Nécessaires, 1 de Rechange Équerre ’utilisez pas de flamme pour vérifier les fuites de gaz Assurez-vous que le gaz est coupéÉtape 7 Ajustez LE Niveau DE LA Étape 7 Ajustez LE Niveau DE LA CuisinièreCuisinière suite Étape 8 Replacez Lales Portes DU FourTerminez L’INSTALLATION Étape 9 Vérifiez LES BrûleursCouvercle d’aération de la plaque chaufffante ACCESSOIRES-PLINTHE fournie Bas dePlinthe Poussez Installez LE Dosseret 30 CM Accessoires EN OPTION-DOSSERET DE 30 CM 12 DE HauteurAvertissement Ce dosseret Ce Kit comprendInstallez LES Panneaux DE Support Mural ACCESSOIRES-DOSSERET Ajustable 30-36 non fourniAvertissement Les panneaux Outils ET Matériel NécessairesInstallez LES Panneaux Installez LES Panneaux DE RecouvrementDE Recouvrement suite Méthode Alternative en cas d’obstruction de l’accès latéralSupport D’ORIFICE Convertir LE RégulateurOrifices DE Miijotage ZDP304 Consignes d’installation pour la conversion de gazMiijotage PrincipauxAjustez LES Flammes DU Brûleur Tiempo de finalización de 1 a 3 horas Antes DE ComenzarModelos a gas natural de Modelos a gas LP deModelo a gas LP de 30 ZDP304L Dimensiones Y Espacios DEL Producto Gas Modelos de cocina deModelos de cocina de 30 de ancho Dimensiones Y Espacios DEL Producto Información de diseñoModelos de cocinas de 48, 36 y KIT DE Reducción WB28K10554 Información de instalaciónMateriales Provistos Herramientas RequeridasUbicaciones DEL Suministro DE Energía Preparación para la instalaciónSuministro de gas Suministro eléctricoInstalación DE Cable DE Energía DE 4 Hilos Instalación DE Cable DE Energía DE 3 HilosNo Quite la cinta de conexión a tierra Paso 1 Quite EL Empaque InstalaciónPara quitar las puertas del horno Quite LAS Puertas DEL Horno SóloQuite la placa de protección de la base de espuma Paso 2 Traslade LA Cocina AL InteriorIncline la cocina hacia un lado y quite el bloque de espuma Placa de protecciónTornillos para madera Piezas anti-volcaduras provistasNo utilice una llama para verificar pérdidas de gas Paso 5 Conecte LA ElectricidadPaso 7 Nivele LA Cocina Ajuste DE LAS Patas DelanterasTornillo de apriete manual Finalice LA Instalación Paso 9 Controle LOS QuemadoresVuelva a chequear los pasos Tapa de ventilación de la planchaAccesorios Placa DE Protección Provisto Parte inferior de laPlaca de protección Presione Instale EL Salpicadero DE Accesorios Opcionales Salpicadero Alto DEHerramientas Y Materiales Requeridos Este kit incluyeAdvertencia Los paneles Accesorios -SALPICADERO Ajustable DE 30 a 36 no incluidoLea estas instrucciones por completo y con detenimiento Instale LOS Paneles DE Cubierta Instale LOS Paneles DE CubiertaInstale Instale El tornillo Instale tornillos en las esquinasHerramientas Necesarias Para LA Conversión Convierta EL ReguladorCambie LOS Orificios DE LOS Quemadores Los orificios y convertir el regulador de presiónCambie LOS Orificios Instrucciones de instalación para conversión de gasDE LOS Quemadores Cambie EL Orificio DE LA Parrilla si correspondeAjuste la configuración de la hilera superior Cambie EL Orificio DE LAPlancha si corresponde GE Consumer & Industrial

Range specifications

The GE Monogram Range stands as a pinnacle of luxury and functionality in the realm of kitchen appliances. Designed for culinary enthusiasts and home chefs alike, this range embodies superior performance, cutting-edge technology, and exquisite craftsmanship. One of the main features of the GE Monogram Range is its impressive cooking power, with true European convection that ensures even baking and precise temperature control, making it ideal for a wide array of cooking techniques.

Equipped with powerful burners, including a 20,000 BTU tri-ring burner, the GE Monogram Range offers versatility for both high-heat searing and low-simmer sauces. The ranges typically feature a combination of gas burners, electric ovens, and induction cooktops, catering to diverse cooking preferences. The gas models provide instant heat adjustments, while the induction options offer faster cooking times and enhanced energy efficiency.

The technology embedded in the GE Monogram Range enhances the cooking experience significantly. With smart technology integration, users can connect the appliance to their smartphones for remote control and monitoring via the GE Appliances app. This feature allows cooks to preheat the oven, adjust cooking temperatures, and even set timers from anywhere in their home.

Another hallmark of the GE Monogram Range is its customizable design. Available in various finishes, including stainless steel and bold colors, these ranges can seamlessly blend into any kitchen aesthetics. The option to select additional features, such as griddle plates and customizable backguards, provides homeowners with the ability to tailor their range to their specific culinary desires.

The self-cleaning feature of the GE Monogram Range is yet another advantage, utilizing high-temperature cleaning that incinerates debris and leaves behind only a fine ash, which can be easily wiped away. This makes maintenance straightforward and keeps the range looking pristine.

Safety is also paramount, with features like a gas safety shut-off valve, which provides peace of mind for families. Additionally, the ranges are equipped with advanced oven controls that include a delay bake option, allowing users to schedule baking to start automatically.

In summary, the GE Monogram Range is a true embodiment of luxury, efficiency, and modern technology, catering to the needs of discerning home chefs. With its standout features and adaptable design, it not only elevates kitchen aesthetics but also transforms cooking into an effortless and enjoyable experience.