GE Monogram Range Change Griddle Orifice if present, Adjust Burner Flames

Page 23

Installation Instructions for Gas Conversion

5 CHANGE GRIDDLE ORIFICE (if present)

Locate the 3/4” long Griddle orifice.

Select for your gas type. LP—.047, NAT—.076

A. Lift off

the griddle flue

 

cover. Remove

Griddle Flue Cover

the 2 inside

A

clamping

screws.

 

6 ADJUST BURNER FLAMES

Normally, burners do not need further adjustment. Make adjustments only when necessary.

A. Turn on the gas. Plug in electrical cord.

B. Turn all burners on highest setting and check

the flames. They should be blue in color. When

using LP gas, the flames may have some yellow

tipping at the ends of the flame. Foreign particles

B. Use a pad or

 

 

piece of

 

 

carton to

 

 

protect

Leveling Screws

the adjacent

surface. Slide

 

 

the griddle

Clamping Screws

toward

the rear

 

 

and out of

 

B

the hold-down tabs along

the bottom.

 

 

NOTE: Remove

the 2 screws positioned on the inside only. Do not remove the outermost screws—they are for leveling.

in the gas line may cause an orange flame at first,

but this will soon disappear.

C. Turn the burner knob to “LO” while observing the

flame.

Adjust the setting of the upper row of flames using the valve bypass screw as follows:

Adjustments must be made with two other burners in operation on a medium setting. This prevents the upper row of flames from being set too low, resulting in the flame being extinguished when other burners are turned on.

C.CAREFULLY lift and hold the griddle. A thermostat capillary is routed through a clip. Gently lift the griddle to one side and slip the capillary out of the clip.

D.Lay the griddle

on the padded surface. Do not disconnect or pull on the capillary.

E.Remove the 2 burner hold-down screws

at the rear of the burner.

•Pull the burner straight back toward the rear and out of the gas inlet.

C

Capillary

D

D.To adjust the flame, remove the knobs. Insert a small flat-blade screwdriver into the hole in the center

of the valve stem to engage screw.

•If the flames are too small or flutter, turn the screw counterclockwise.

F.Use a 1/2" deep well socket

to remove and replace the orifice.

E

Back of Range

F

Front of Range

Reverse these steps to re-assemble the griddle. Push excess capillary back into the entry hole. Route the thermostat capillary so it is held by the clip. Place the unused orifice in the holder for possible future use.

•If the flames are too large, turn the screw clockwise.

E.Make the adjustment by slowly turning the screw until flame appearance is correct.

Once the conversion is complete and checked, fill out the conversion label and affix the label near the rating label. For ranges, place the label beneath the control panel. For rangetops, place the label on the bottom of the unit.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Instrucciones de instalación Instructions d’installationRead these instructions completely and carefully Installation InstructionsVent hood Combinations Completion Time 1 to 3 hoursModels Available ContentsBacksplash Accessories Design InformationRange Models Design InformationTo 4-3/4 Toekick/leg Height Minimum To Adjacent Wall Above the range and below Wide Range Models48, 36 and 30 Range Models Product Dimensions and ClearancesMaterials Provided Installation InformationWB28K10553 High Altitude KIT WB28K10554 DE-RATE KITGas Supply Installation PreparationPower Supply Locations See 3-wire power cord installation on the nextDo not remove the ground strap connection Wire Power Cord InstallationTo remove the oven doors InstallationRemove Packaging Tilt the range to lower the hand-truck wheels off the skid Move the Range IndoorsTilt the range forward on the skid Lift the toekick out of the foam baseAnti-Tip Bracket Anti-Tip Brace Aham Anti-Tip Safety BrochureAnti-Tip Parts Provided Hex Screws Anti-Tip Brace Alternate Brace PositionAssure that gas supply is turned off at the shut-off valve Connect Range to GASRoll Range Into Position Connect ElectricalLevel the Range Front LEG AdjustmentRear LEG Adjustment Level the RangeRecheck Steps Finalize InstallationInstallation Checklist Check BurnersToekick Push ACCESSORIES-TOEKICK providedTop Toekick Bottom This Kit Includes Optional ACCESSORIES-12 High BacksplashInstall 12 Backsplash Tools and Materials RequiredMaximum shelf load-bearing weight is 40 lbs ACCESSORIES-30 to 36 Adjustable Backsplash not includedInstall the Wall Support Panels Alternate Method When side access is blocked Install Cover PanelsInstall Cover Panels See alternate method if side access is blockedChange Burner Orifices Convert the RegulatorTools YOU Needed for Conversion ZDP364, ZDP366, ZDP484, ZDP486 Installation Instructions for Gas ConversionChange Burner Orifices Change Grill Orifice if presentChange Griddle Orifice if present Adjust Burner FlamesDispositions de hotte d’extraction Consignes d’installationRemarque à l’attention de l’installateur Temps d’installation 1 à 3 heuresDosseret CaractéristiquesTable DES Matières Modèles DisponiblesModèles de cuisinière 121 cm Dimensions DU Produit ET Espaces DE SéparationModèles de cuisinière 91 cm 36’’ Caractéristiques Dimensions DE L’APPAREIL ET EspacesModèles de cuisinière 76 cm 30’’ Dimensions DE L’APPAREIL ET Espaces28-1/4 70,96 cm Jusquà lavant de la porte Modèles de cuisinière 76 cm 30’’, 91 cm 36’’ et 121 cm10-1/2 24,13 cm 13/16 2 cm Dosseret 30-36 En option Outils Nécessaires KIT Haute Altitude WB28K10553KIT DE Réduction DES Caractéristiques Nominales WB28K10554 Matériel FourniAlimentation électrique Préparation de l’installationEmplacement DES Alimentations Alimentation de gazNE retirez PAS le branchement du conducteur de terre Installation DU Cordon ’ALIMENTATION 4 FilsInstallation DU Cordon ’ALIMENTATION 3 Fils Rainure Verrou de charnière Étape 1 Sortez L’APPAREIL DE SON EmballagePour retirer lales portes AttachesPlinthe Étape 2 Déplacez LA Cuisinière À L’INTÉRIEURSoulevez la plinthe du socle en mousse Vis à tête hexagonale Nécessaires, 1 de Rechange Équerre Pièces du support anti-basculement fourniesVis à bois ’utilisez pas de flamme pour vérifier les fuites de gaz Assurez-vous que le gaz est coupéÉtape 8 Replacez Lales Portes DU Four Étape 7 Ajustez LE Niveau DE LA CuisinièreÉtape 7 Ajustez LE Niveau DE LA Cuisinière suiteCouvercle d’aération de la plaque chaufffante Terminez L’INSTALLATIONÉtape 9 Vérifiez LES Brûleurs Plinthe Poussez ACCESSOIRES-PLINTHE fournieBas de Ce Kit comprend Accessoires EN OPTION-DOSSERET DE 30 CM 12 DE HauteurInstallez LE Dosseret 30 CM Avertissement Ce dosseretOutils ET Matériel Nécessaires ACCESSOIRES-DOSSERET Ajustable 30-36 non fourniInstallez LES Panneaux DE Support Mural Avertissement Les panneauxMéthode Alternative en cas d’obstruction de l’accès latéral Installez LES Panneaux DE RecouvrementInstallez LES Panneaux DE Recouvrement suiteSupport D’ORIFICE Convertir LE RégulateurPrincipaux Consignes d’installation pour la conversion de gazOrifices DE Miijotage ZDP304 MiijotageAjustez LES Flammes DU Brûleur Tiempo de finalización de 1 a 3 horas Antes DE ComenzarModelo a gas LP de 30 ZDP304L Modelos a gas natural deModelos a gas LP de Dimensiones Y Espacios DEL Producto Gas Modelos de cocina deModelos de cocina de 30 de ancho Modelos de cocinas de 48, 36 y Dimensiones Y Espacios DEL ProductoInformación de diseño Herramientas Requeridas Información de instalaciónKIT DE Reducción WB28K10554 Materiales ProvistosSuministro eléctrico Preparación para la instalaciónUbicaciones DEL Suministro DE Energía Suministro de gasNo Quite la cinta de conexión a tierra Instalación DE Cable DE Energía DE 4 HilosInstalación DE Cable DE Energía DE 3 Hilos Quite LAS Puertas DEL Horno Sólo InstalaciónPaso 1 Quite EL Empaque Para quitar las puertas del hornoPlaca de protección Paso 2 Traslade LA Cocina AL InteriorQuite la placa de protección de la base de espuma Incline la cocina hacia un lado y quite el bloque de espumaTornillos para madera Piezas anti-volcaduras provistasNo utilice una llama para verificar pérdidas de gas Paso 5 Conecte LA ElectricidadTornillo de apriete manual Paso 7 Nivele LA CocinaAjuste DE LAS Patas Delanteras Tapa de ventilación de la plancha Paso 9 Controle LOS QuemadoresFinalice LA Instalación Vuelva a chequear los pasosPlaca de protección Presione Accesorios Placa DE Protección ProvistoParte inferior de la Este kit incluye Accesorios Opcionales Salpicadero Alto DEInstale EL Salpicadero DE Herramientas Y Materiales RequeridosLea estas instrucciones por completo y con detenimiento Advertencia Los panelesAccesorios -SALPICADERO Ajustable DE 30 a 36 no incluido Instale El tornillo Instale tornillos en las esquinas Instale LOS Paneles DE CubiertaInstale LOS Paneles DE Cubierta InstaleLos orificios y convertir el regulador de presión Convierta EL ReguladorHerramientas Necesarias Para LA Conversión Cambie LOS Orificios DE LOS QuemadoresCambie EL Orificio DE LA Parrilla si corresponde Instrucciones de instalación para conversión de gasCambie LOS Orificios DE LOS QuemadoresPlancha si corresponde Ajuste la configuración de la hilera superiorCambie EL Orificio DE LA GE Consumer & Industrial

Range specifications

The GE Monogram Range stands as a pinnacle of luxury and functionality in the realm of kitchen appliances. Designed for culinary enthusiasts and home chefs alike, this range embodies superior performance, cutting-edge technology, and exquisite craftsmanship. One of the main features of the GE Monogram Range is its impressive cooking power, with true European convection that ensures even baking and precise temperature control, making it ideal for a wide array of cooking techniques.

Equipped with powerful burners, including a 20,000 BTU tri-ring burner, the GE Monogram Range offers versatility for both high-heat searing and low-simmer sauces. The ranges typically feature a combination of gas burners, electric ovens, and induction cooktops, catering to diverse cooking preferences. The gas models provide instant heat adjustments, while the induction options offer faster cooking times and enhanced energy efficiency.

The technology embedded in the GE Monogram Range enhances the cooking experience significantly. With smart technology integration, users can connect the appliance to their smartphones for remote control and monitoring via the GE Appliances app. This feature allows cooks to preheat the oven, adjust cooking temperatures, and even set timers from anywhere in their home.

Another hallmark of the GE Monogram Range is its customizable design. Available in various finishes, including stainless steel and bold colors, these ranges can seamlessly blend into any kitchen aesthetics. The option to select additional features, such as griddle plates and customizable backguards, provides homeowners with the ability to tailor their range to their specific culinary desires.

The self-cleaning feature of the GE Monogram Range is yet another advantage, utilizing high-temperature cleaning that incinerates debris and leaves behind only a fine ash, which can be easily wiped away. This makes maintenance straightforward and keeps the range looking pristine.

Safety is also paramount, with features like a gas safety shut-off valve, which provides peace of mind for families. Additionally, the ranges are equipped with advanced oven controls that include a delay bake option, allowing users to schedule baking to start automatically.

In summary, the GE Monogram Range is a true embodiment of luxury, efficiency, and modern technology, catering to the needs of discerning home chefs. With its standout features and adaptable design, it not only elevates kitchen aesthetics but also transforms cooking into an effortless and enjoyable experience.
Top Page Image Contents