Graco important safety instructions Tables 4 PR70 Screen Icon Tables

Page 27

ICON Tables

ICON	Description	Screen
	Short Stroke Calibration Shot	C4

	Long Stroke Calibration Shot	C4

	Administrative Password Set/Clear	C5

	Maintenance Only Screens Password Set/Clear	C5

	Tank Level Sensing ON	C6

	Tank Level Sensing OFF	C6

	Delta Velocity Set Level (0 = OFF)	C6

	Displacement Valve Always Open	M1

	Displacement Valve Always Closed	M1

	Displacement Valve Automatic Operation	M1

	Shot Size Definition	M2

	Purge Timer Set/Clear	M2

	Purge Shot Size	M2

	Purge Alarm Setting	M2

	Zero Cycle Counter	M3

	Silent Mode ON	M3

	Silent Mode OFF	M3

	Set Date	M4

	Set Time	M4

	Tables 4: PR70 Screen ICON Tables (Continued)

312393G

27 of 50

Image 27

Contents PR70 Contents Mixer and Shroud Options PR70 AccessoriesDescription Supplied ManualsRelated Manuals PR70 Feed SystemElectric Shock Hazard Equipment Misuse Hazard General Information InstallationLocate and Install the PR70 Machine SetupKey Component IdentificationPR70 Top View with Shield, Tanks, DV and HMI Removed HMI Control and IndicatorsRun Screen Operation Setup Screens with Passwords Enabled Machine Disable Mode redSetup Screens Entering the Setup ScreensPR70 Screen Navigation Diagram Machine Priming Machine CalibrationPiston Position Calibration C1 Phasing C2 Open Dispense Valve ODV Setting C3Open Dispense Valve ODV Screen C3 Key Machine Calibration Shots C4Ratio Checks Shot Size Definition M2Manual DV Control Miscellaneous Machine SetupsPurge Timer / Alarm Settings M2 Manual Control Options M1M2 after Purge Shot Size Prompt Cycle Counter and Silent Mode Control M3Tank Level Sensing and Velocity Change Options C6 Date and Time Settings M4Setting/Clearing an Administrative Password Password Setup / Clearing C5Setting/Clearing a Maintenance only Password Resetting PasswordsTo clear the password, enter Limitations of Demo Mode Simulation Miscellaneous Machine FeaturesHMI Hibernate Mode HMI Demo Mode OperationPressure Relief Procedure Standby/Shutdown ProcedureError Codes Error Code Table Error Code Table E29E50 Key Key Description Screen PR70 HMI Icon TableTables 3 PR70 Screen Icon Tables Tables 4 PR70 Screen Icon Tables Maintenance Software Upgrades, Run TokenRun Token Problem Cause Solution TroubleshootingMajor Mechanical Assemblies, and Attachments RepairPR70 Base Frame Assembly LC0109 Key Base Frame AssemblyAir Cylinder Assemblies, and Rebuild Kits PR70 Air Cylinder System and SchematicAir Cylinder Assemblies Pump Assembly Pump Assemblies and Rebuild Kits Drive Block AssemblyPR70 Check Valve Rebuild Kit LC0093 Key To install a new Check Valve Rebuild KitPR70 Rear Pump Rebuild Kit LC0094 Key To install a new Rear Pump Rebuild KitPiston Cylinders or Metering Tubes PR70 Nylon and Uhmwpe Piston Replacement Kits KeyNylon Pistons see Figure To install a new Piston or Piston/Cylinder Replacement KitAvailable PR70 Piston and Cylinder Metering Tubes Kits Key Hose Assemblies To install a new Piston Plug AssemblyHeated Piston to DV Hose Assemblies To Replace the Fuses Miscellaneous Mechanical AssembliesPR70 Control Bracket Assembly LC0108 Key PR70 Hydracheck Components PR70 Wiring Interconnect Illustration Wiring DiagramsWiring Diagram, PR70 Category Data Technical DataPR70 Dimensions ON-Board PE Tank version Illustrated DimensionsGraco Information Graco Ohio Standard Warranty