Graco HMI Control and Indicators, PR70 Top View with Shield, Tanks, DV and HMI Removed

Page 9

Component Identification

Key:

A Drive Block

B Hydracheck (optional)

C Check Valve

D Cylinder (Metering Tube)

E Rear Bearing

F Phase Adjustment Screw/Locking

Nut

G Mounting Hole in Base Frame

Figure 4: PR70 Top View with Shield, Tanks, DV and HMI Removed.

HMI Control and Indicators

Figure 5: PR70 HMI Controls

Key:
A	Screen, Display Area	N	Operator Mode ICON
B, D	Up and Down Keys	O	Operator Mode LED
C	Up and Down Key LED	P	Red Stop or Cancel Key (used to stop machine
E	Enter Key LED		operation)
F	Enter Key	Q	Lock Key (used to enter and exit setup screens)
G-J	Soft Keys 1 thru 4 (Left to Right).	R	Green Go Key (used to request a shot)
K	Shot Mode ICON	S	Display area
L	Shot Mode LED	T	Diagnostic LED’s
M	Mode Select Key	U	HMI Rear Access Panel (used to access clock
			battery and for reprogramming the HMI).

312393G

9 of 50

Image 9

Contents PR70 Contents Mixer and Shroud Options PR70 AccessoriesRelated Manuals Supplied ManualsPR70 Feed System DescriptionElectric Shock Hazard Equipment Misuse Hazard Locate and Install the PR70 InstallationMachine Setup General InformationKey Component IdentificationPR70 Top View with Shield, Tanks, DV and HMI Removed HMI Control and IndicatorsRun Screen Operation Setup Screens Machine Disable Mode redEntering the Setup Screens Setup Screens with Passwords EnabledPR70 Screen Navigation Diagram Machine Priming Machine CalibrationPiston Position Calibration C1 Phasing C2 Open Dispense Valve ODV Setting C3Open Dispense Valve ODV Screen C3 Key Machine Calibration Shots C4Ratio Checks Shot Size Definition M2Purge Timer / Alarm Settings M2 Miscellaneous Machine SetupsManual Control Options M1 Manual DV ControlM2 after Purge Shot Size Prompt Cycle Counter and Silent Mode Control M3Tank Level Sensing and Velocity Change Options C6 Date and Time Settings M4Setting/Clearing an Administrative Password Password Setup / Clearing C5Setting/Clearing a Maintenance only Password Resetting PasswordsTo clear the password, enter HMI Hibernate Mode Miscellaneous Machine FeaturesHMI Demo Mode Operation Limitations of Demo Mode SimulationPressure Relief Procedure Standby/Shutdown ProcedureError Codes Error Code Table Error Code Table E29E50 Key Key Description Screen PR70 HMI Icon TableTables 3 PR70 Screen Icon Tables Tables 4 PR70 Screen Icon Tables Maintenance Software Upgrades, Run TokenRun Token Problem Cause Solution TroubleshootingMajor Mechanical Assemblies, and Attachments RepairPR70 Base Frame Assembly LC0109 Key Base Frame AssemblyAir Cylinder Assemblies, and Rebuild Kits PR70 Air Cylinder System and SchematicAir Cylinder Assemblies Pump Assembly Pump Assemblies and Rebuild Kits Drive Block AssemblyPR70 Check Valve Rebuild Kit LC0093 Key To install a new Check Valve Rebuild KitPR70 Rear Pump Rebuild Kit LC0094 Key To install a new Rear Pump Rebuild KitPiston Cylinders or Metering Tubes PR70 Nylon and Uhmwpe Piston Replacement Kits KeyNylon Pistons see Figure To install a new Piston or Piston/Cylinder Replacement KitAvailable PR70 Piston and Cylinder Metering Tubes Kits Key Hose Assemblies To install a new Piston Plug AssemblyHeated Piston to DV Hose Assemblies To Replace the Fuses Miscellaneous Mechanical AssembliesPR70 Control Bracket Assembly LC0108 Key PR70 Hydracheck Components PR70 Wiring Interconnect Illustration Wiring DiagramsWiring Diagram, PR70 Category Data Technical DataPR70 Dimensions ON-Board PE Tank version Illustrated DimensionsGraco Information Graco Ohio Standard Warranty