Graco important safety instructions PR70 Base Frame Assembly LC0109 Key

Page 31

Base Frame and Air Cylinder Assemblies

Figure 40: PR70 Power Entry Bracket and Control Bracket Assembly Attachments

Key:

Ref

P/N

Description

QTY

Ref

P/N

Description

QTY

1

120885

Screw, SHC, M5 – 0.8 x 14

4

3

LC0106

Power Entry Assembly, PR70

1

2

LC0108

Control Bracket Assembly, PR70

1

4

120885

Screw, SHC, M5 – 0.8 x 14

2

Base Frame Assembly

Figure 41: PR70 Base Frame Assembly (LC0109)

Key:

Ref

P/N

Description

QTY

Ref

P/N

Description

QTY

1

120599

PIN, DOWEL, 3/8DIAX1.50LG, SS

2

5

15K796

CLAMP

1

2

120885

SCREW,SHC, M5-0.8X14,MS,E

2

6

LC0033

TRANSDUCER ASSY, LINEAR, PR70S

1

3

120913

SCREW,SHC, M8X1.25X25,MS, E

2

7

120918

GUIDE, LINEAR

1

4

15K788

FRAME, BASE, PR70S, MACHINED

1

8

120886

SCREW, SHC,M6-1.0X25,MS,E

4

312393G

31 of 50

Image 31
Contents PR70 Contents Mixer and Shroud Options PR70 AccessoriesDescription Supplied ManualsRelated Manuals PR70 Feed SystemElectric Shock Hazard Equipment Misuse Hazard General Information InstallationLocate and Install the PR70 Machine SetupKey Component IdentificationPR70 Top View with Shield, Tanks, DV and HMI Removed HMI Control and IndicatorsRun Screen Operation Setup Screens with Passwords Enabled Machine Disable Mode redSetup Screens Entering the Setup ScreensPR70 Screen Navigation Diagram Machine Calibration Machine PrimingPiston Position Calibration C1 Phasing C2 Open Dispense Valve ODV Setting C3Open Dispense Valve ODV Screen C3 Key Machine Calibration Shots C4Ratio Checks Shot Size Definition M2Manual DV Control Miscellaneous Machine SetupsPurge Timer / Alarm Settings M2 Manual Control Options M1M2 after Purge Shot Size Prompt Cycle Counter and Silent Mode Control M3Tank Level Sensing and Velocity Change Options C6 Date and Time Settings M4Setting/Clearing an Administrative Password Password Setup / Clearing C5Resetting Passwords Setting/Clearing a Maintenance only PasswordTo clear the password, enter Limitations of Demo Mode Simulation Miscellaneous Machine FeaturesHMI Hibernate Mode HMI Demo Mode OperationStandby/Shutdown Procedure Pressure Relief ProcedureError Codes Error Code Table E29 Error Code TableE50 PR70 HMI Icon Table Key Key Description ScreenTables 3 PR70 Screen Icon Tables Tables 4 PR70 Screen Icon Tables Software Upgrades, Run Token MaintenanceRun Token Problem Cause Solution TroubleshootingMajor Mechanical Assemblies, and Attachments RepairPR70 Base Frame Assembly LC0109 Key Base Frame AssemblyAir Cylinder Assemblies, and Rebuild Kits PR70 Air Cylinder System and SchematicAir Cylinder Assemblies Pump Assembly Pump Assemblies and Rebuild Kits Drive Block AssemblyPR70 Check Valve Rebuild Kit LC0093 Key To install a new Check Valve Rebuild KitPR70 Rear Pump Rebuild Kit LC0094 Key To install a new Rear Pump Rebuild KitPiston Cylinders or Metering Tubes PR70 Nylon and Uhmwpe Piston Replacement Kits KeyNylon Pistons see Figure To install a new Piston or Piston/Cylinder Replacement KitAvailable PR70 Piston and Cylinder Metering Tubes Kits Key Hose Assemblies To install a new Piston Plug AssemblyHeated Piston to DV Hose Assemblies To Replace the Fuses Miscellaneous Mechanical AssembliesPR70 Control Bracket Assembly LC0108 Key PR70 Hydracheck Components PR70 Wiring Interconnect Illustration Wiring DiagramsWiring Diagram, PR70 Category Data Technical DataPR70 Dimensions ON-Board PE Tank version Illustrated DimensionsGraco Information Graco Ohio Standard Warranty