GE C2S980, 04-09 JR, 49-85167-1 Using the clock and timer, Instructions Safety, Troubleshooting

Page 16

Instructions

Using the clock and timer.

Not all features are on all models.

Instructions Safety

Make sure the clock is set to the correct time of day.

To Set the Clock

The clock must be set to the correct time of day for the automaticoven timing functions to work properly. The time of day cannot be changed during a timed baking or self-cleaning cycle.

Touch the CLOCK pad.

Touch the number pads.

Touch the number pads the same way you read them. For example, to set 12:34, touch the number pads 1, 2, 3 and 4 in that order.

If number pads are not touched within one minute after you touch the CLOCK pad, the display reverts to the original setting. If this happens, touch the CLOCK pad and reenter the time of day.

Touch the START pad until the time

of day shows in the display. This enters the time and starts the clock.

To check the time of day when the display is showing other information, simply touch the CLOCK pad. The time of day shows until another pad is touched.

Operating

Installation

Instructions

 

 

Tips

The timer is a minute timer only.

The CLEAR/OFF pad does not affect the timer.

To Set the Timer

The timer does not control ovenoperations. The maximum settingon the timer is 9 hours and 59 minutes.

Touch the KITCHEN TIMER ON/OFF pad.

Touch the number pads until the amount of time you wantshows in the display. The maximum number of minutes that can be entered is 60. To set additional time, you will need to set it by hours and minutes.

For example, to enter 1 hour and 30 minutes, touch 1, 3 and 0 in that order.

If you make a mistake, press the KITCHEN TIMER ON/OFF pad and begin again.

Touch the START pad. After pressing the START pad, SET disappears; this tells you the time is counting down, although the display does not change until one minute has passed.

When the timer reaches :00, the control will beep 3 times followed by one beep every 6 seconds until the KITCHEN TIMER ON/OFF pad is touched.

The 6 second tone can be canceled by following the steps in the Special features of your oven control section under Tones at the End of a Timed Cycle.

Troubleshooting

To Reset the Timer

If the displayis still showing the time remaining, you may change it by touching the KITCHEN TIMER ON/OFF pad; then touch the number pads until the time you want appears in the display.

If the remaining time is not in the display (clock, delay start or cooking time are in the display), recall the remaining time by touching the KITCHEN TIMER ON/OFF pad and then touching the number pads to enter the new time you want.

Consumer Support

To Cancel the Timer

Touch the KITCHEN TIMERON/OFF pad twice.

Power Outage

If a flashingtime is in the display, you have

To reset the clock, touch the CLOCK pad.

experienced a power failure. Reset the clock.

Enter the correct time of day by touching the

 

appropriate number pads. Touch the START

 

pad.

16

Image 16
Contents Safety Instructions Write the model and serial numbers here Model # Serial #What to do if YOU Smell GAS Troubleshooting Tips Consumer Support Safety Instructions Operating InstructionsGEAppliances.com Installation Instructions Operating Instructions Safety InstructionsConsumer Support Safety Safety Instructions SurfaceburnersLoweroven Drawer Instructions Safety Instructions Operating Installation InstructionsSupport Troubleshooting TipsUsingthe gas surface burners SafetyInstructions Installation Instructions OperatingUsing the griddle Safety InstructionsHow to Insert the Griddle Using the GriddleTroubleshooting Tips Using the gas surface burnersInstructions Operating Instructions Operating Instructions Safety Instructions Using the upperoven controlsIf your oven was set for a timed oven operation Usingthe upper oven InstructionsBefore you begin… Upper Oven VentInstallation Instructions Tips Using the upperovenOperating Broiling Guide How to Set the Upper Oven for Broiling-Close the oven doorHI Broil Instructions Safety Using the clock and timerTroubleshooting How to Set a Delayed Start and Automatic Stop Using the timedbaking Roasting featuresupperovenonlyOperating Instructions Operating Instructions Safety Using the probeHow to Set the Upper Oven For Roasting When Using the Probe Convection Bake Using the convection ovenConvection Roast Installation Instructions Troubleshooting Tips How to Set the Upper Oven for Convection Baking or RoastingCookware for Convection Cooking Multi-Rack BakingTouch the Convectionroast pad Convection Roasting Guide Using the timedconvection Baking features upper ovenonly How to Set an Immediate Start and Automatic StopSpecial features of yourupperoven control Fahrenheit or Celsius Temperature SelectionHour Shut-Off Tones at the End of a Timed CycleTo turn off this feature Gas/Control Lockout on some modelsHour, 24-Hour or Clock Blackout Auto Recipe ConversionHow to Set for Regular Baking/Roasting Using the Sabbath Feature.on some modelsHow to Exit the Sabbath Feature To Adjust the Thermostat Adjustthe upperoven thermostat-Do it yourselfType of margarine will affectbaking performance Adjust the oventhermostat-Doit yourself Using the lowerovendrawerTo Use the Lower Oven Drawer Before a Clean Cycle Usingthe self-cleaningupper ovenHow to Set the Upper Oven for Cleaning How to Delay the Start of Cleaning Using the self-cleaningupperovenAfter a Clean Cycle Care and cleaning of the range Sealed Burner AssembliesCare and cleaningof the range Burner Caps and HeadsBurner Grates Tips Consumer SupportCooktop Surface Griddle Precautions GriddleStainless Steel Surfaces on some models ProtectingTo clean the insideof the door To clean the outside of the doorLift-Off Oven Door Oven Heating ElementsRemovable Lower Oven Drawer Removable Lower Oven Drawer PanGlass Window To remove the drawer To replace the drawerUpper Control Panel Oven Air VentsLower Control Panel and Knobs Oven Light Replacement Oven Racks and Drawer RacksTo remove Do not remove any screws to remove the coverInstallation of the range Instructions InstallationIf you smell gas Read these instructions completely and carefullyInstallation Instructions Installationof the rangeOperating Instructions Dimensions and Clearances Operating Instructions Safety Tools YOU will NeedProvide Adequate Gas Supply Gas Supply RequirementsRecommended Gas Pipe Outlet Locations Electrical Power Supply Requirements Provide Proper Electrical SupplyRecommended Electrical Outlet Locations Wall MountedConnect the Range to the Gas Supply Flexible Connector HookupRigid Pipe Hookup Options Replace the Power Cord Optional Using an Existing Nema 14-50R ReceptacleDo not discard these screws Wire Power Cord Installation Option Wire Conduit Installation Option Troubleshooting Replace the Wire Cover Wire used, location and enclosureSplices, etc., must conformto good wiring Tips ConsumerSeal the Openings OperatingAssemble Surface Burners Safety Instructions Operating Check Ignition of Surface BurnersQuality of Flames Level the RangeAnti-Tip Device Installation When All Hookups Are CompletedBefore you callfor service… Troubleshooting Tips Consumer SupportProblem Possible Causes What To Do InstructionsOperating Instructions Safety Instructions Installation Before you call for service…Consumer Support Troubleshooting Tips Safety Instructions Operating Instructions Installation Before you call for service… Accessories Looking For Something More?Instructions Ownership Registration Page Page Instructions Safety Instructions GE Will ReplaceWhat GE Will Not Cover For The PeriodGE Dual FuelRangeWarranty.For customers in Canada Mabe Will ReplaceWhat Mabe Will Not Cover For The PeriodOfConsumer Support GE Appliances Website
Related manuals
Manual 64 pages 54.85 Kb

183D5580P249, 49-85167-1, 04-09 JR, C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.