GE 04-09 JR Tips Consumer, Troubleshooting Replace the Wire Cover, Practices and local codes

Page 49

Read these instructions completely and carefully.

Replace the Power Cord (Optional) (Continued)

Perform this step only if the power cord shipped on the range does not matchyour wallreceptacle.

4-Wire Conduit Installation Option

Safety Instructions

Removethe strain relief clampfrom the bracket.

Assemble the squeeze connector(obtained locally), matching the diameter of your conduit, in the bracket hole. Insert the conduit through the squeeze connector.Allow enough slack to easily attach the wires to the terminal block.

NOTE: Do not install the conduit without a squeeze connector.

Insert the ground barewiretip betweenthe range frame and the ground plate (removed earlier) and secure it in placewith the ground screw (removed earlier). Insert the barewire (white/neutral) tip through the bottom center of the terminalblock opening. Insert the two side barewire tips into the lowerleft and the lower right terminal block openings.Tighten the screws until the wireis firmly secure (approximately 20 inch-lbs.).

NOTE: Make sure the wireis completely inserted into the terminal blockand a secure connection is made.

Squeeze connector

Conduit

Bracket

 

Terminal

 

block

Ground plate

 

Wire tips

(groundingto

range)

Ground

 

screw

 

Operating Instructions

Secure the squeeze connector in placein the

Bracket

bracket by tightening the squeeze connector

screws.

 

NOTE: ALUMINUM WIRING:

 

Aluminum building wire may be used but it must

Wire used, location and enclosure

of splices, etc., must conformto good wiring

be rated for the correctamperage and voltage

practices and local codes.

to make connection.

 

Troubleshooting

Replace the Wire Cover

Replace the wirecover on the range back by sliding its right edge under the retaining tab and replacing the two screws removed earlier.Make sure that no wires are pinched between the cover and the rangeback.

2screws to replacewire cover

Retaining tab

Wire

cover

Tips Consumer

Back of range

49

Support

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Write the model and serial numbers here Model # Serial # Safety InstructionsWhat to do if YOU Smell GAS Troubleshooting Tips Consumer Support Safety Instructions Operating InstructionsGEAppliances.com Installation Instructions Operating Instructions Safety InstructionsConsumer Support Safety Surfaceburners Safety InstructionsLoweroven Drawer Operating Installation Instructions Instructions Safety InstructionsSupport Troubleshooting TipsSafety Usingthe gas surface burnersInstructions Installation Instructions OperatingSafety Instructions Using the griddleHow to Insert the Griddle Using the GriddleTroubleshooting Tips Using the gas surface burnersInstructions Operating Instructions Operating Instructions Safety Instructions Using the upperoven controlsIf your oven was set for a timed oven operation Instructions Usingthe upper ovenBefore you begin… Upper Oven VentInstallation Instructions Tips Using the upperovenOperating Broiling Guide How to Set the Upper Oven for Broiling-Close the oven doorHI Broil Instructions Safety Using the clock and timerTroubleshooting How to Set a Delayed Start and Automatic Stop Using the timedbaking Roasting featuresupperovenonlyOperating Instructions Operating Instructions Safety Using the probeHow to Set the Upper Oven For Roasting When Using the Probe Convection Bake Using the convection ovenConvection Roast How to Set the Upper Oven for Convection Baking or Roasting Installation Instructions Troubleshooting TipsCookware for Convection Cooking Multi-Rack BakingTouch the Convectionroast pad Convection Roasting Guide How to Set an Immediate Start and Automatic Stop Using the timedconvection Baking features upper ovenonlyFahrenheit or Celsius Temperature Selection Special features of yourupperoven controlHour Shut-Off Tones at the End of a Timed CycleGas/Control Lockout on some models To turn off this featureHour, 24-Hour or Clock Blackout Auto Recipe ConversionHow to Set for Regular Baking/Roasting Using the Sabbath Feature.on some modelsHow to Exit the Sabbath Feature To Adjust the Thermostat Adjustthe upperoven thermostat-Do it yourselfType of margarine will affectbaking performance Adjust the oventhermostat-Doit yourself Using the lowerovendrawerTo Use the Lower Oven Drawer Before a Clean Cycle Usingthe self-cleaningupper ovenHow to Set the Upper Oven for Cleaning How to Delay the Start of Cleaning Using the self-cleaningupperovenAfter a Clean Cycle Sealed Burner Assemblies Care and cleaning of the rangeBurner Caps and Heads Care and cleaningof the rangeBurner Grates Tips Consumer SupportCooktop Surface Griddle Griddle PrecautionsStainless Steel Surfaces on some models ProtectingTo clean the outside of the door To clean the insideof the doorLift-Off Oven Door Oven Heating ElementsRemovable Lower Oven Drawer Pan Removable Lower Oven DrawerGlass Window To remove the drawer To replace the drawerUpper Control Panel Oven Air VentsLower Control Panel and Knobs Oven Racks and Drawer Racks Oven Light ReplacementTo remove Do not remove any screws to remove the coverInstructions Installation Installation of the rangeIf you smell gas Read these instructions completely and carefullyInstallation Instructions Installationof the rangeOperating Instructions Dimensions and Clearances Tools YOU will Need Operating Instructions SafetyProvide Adequate Gas Supply Gas Supply RequirementsRecommended Gas Pipe Outlet Locations Provide Proper Electrical Supply Electrical Power Supply RequirementsRecommended Electrical Outlet Locations Wall MountedConnect the Range to the Gas Supply Flexible Connector HookupRigid Pipe Hookup Options Replace the Power Cord Optional Using an Existing Nema 14-50R ReceptacleDo not discard these screws Wire Power Cord Installation Option Wire Conduit Installation Option Wire used, location and enclosure Troubleshooting Replace the Wire CoverSplices, etc., must conformto good wiring Tips ConsumerSeal the Openings OperatingAssemble Surface Burners Check Ignition of Surface Burners Safety Instructions OperatingQuality of Flames Level the RangeWhen All Hookups Are Completed Anti-Tip Device InstallationTroubleshooting Tips Consumer Support Before you callfor service…Problem Possible Causes What To Do InstructionsOperating Instructions Safety Instructions Installation Before you call for service…Consumer Support Troubleshooting Tips Safety Instructions Operating Instructions Installation Before you call for service… Looking For Something More? AccessoriesInstructions Ownership Registration Page Page GE Will Replace Instructions Safety InstructionsWhat GE Will Not Cover For The PeriodMabe Will Replace GE Dual FuelRangeWarranty.For customers in CanadaWhat Mabe Will Not Cover For The PeriodOfGE Appliances Website Consumer Support
Related manuals
Manual 64 pages 54.85 Kb

183D5580P249, 49-85167-1, 04-09 JR, C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.
Top Page Image Contents