Thermador UCVM30FS, UCVM36FS manual Ductwork Installation Guidelines

Page 9

DUCTWORK INSTALLATION GUIDELINES

For safety reasons, ducting should vent directly outdoors (not into an attic, underneath the house, into the garage or into any enclosed space).

Keep duct runs as short and straight as possible.

Duct fittings (elbows and transitions) reduce air flow efficiency.

Back to back elbows and ”S” turns give very poor delivery and are not recommended.

A short straight length of duct at the inlet of the remote blower gives the best delivery.

Transition to duct from the integral blo- wer or remote duct transition as close to the downdraft as is possible. In order of preference, use

1st. 10” round duct 2nd. 8” round duct 3rd. 3-1/4” x 14” duct 4th. 7” round duct 5th. 3-1/4” x 10” duct 6th. 6” round duct

The use of flexible metal round duct should only be used when no other duct fitting exists. Limit use to short lengths and do not crush when making corners.

DUCTWORK INSTALLATION GUIDELINES

Where local codes permit, plastic pipe (PVC-schedule 40 pipe or ABS pipe 7” or 8” diameter) can be used in areas of high ground moisture and in slab floors to eliminate future rusting.

Use only duct work constructed of materials that are acceptable by the applicable codes. All duct should be

26 gauge or heavier to minimize flex due to air flow.

The remote blowers requires a 10” or 8” diameter round duct (depending on model) to match the inlet ring. A transition is necessyary from other duct sizes.

Use sheet metal screws as required to support the duct weight, and seal all joints with duct tape.

Be certain that the duct work does not interfere with floor joists or wall studs.

Do not exhaust more than one vent into a single duct run.

Thermal breaks, such as a short section of nonmetallic duct, should be used in areas of extreme cold.

Always use an appropriate roof or wall-cap with damper. Laundry type wall caps should never be used.

9

Image 9
Contents Model UCVM30FS / UCVM36FS Página Safety Instructions Parts Needed Parts Supplied Plan the installation IntroductionGeneral Description Page Figures 3 through 6 are examples of possible ducting Total of both columns= Ductwork Installation Guidelines Ductwork Installation GuidelinesPrepare Countertop Cutout Installation Dimensions with Thermador Cooktop Cooktops Installed with UCVM30FSCooktops Installed with UCVM36FS CCD COD CW = CCW For Installation with Another Brand of Cooktop FigurePrepare Duct Cutouts Cabinet Prepare Duct Cutouts in CabinetInstall Ductwork Remote Blower, If Used Install Electrical ServiceMount Vent and Cooktop Integral Blower VTN600CV2C see Figures 12 for further detail CV2T6 Switch Verify Installation, Operation and Cooktop Alignment Instructions DE Sécurité Pièces fournies Pièces nécessairesDescription Générale Étape 1 Plan d’installation4 po 16 po Figures 3 à 6 sont des exemples de conduits 10 po Tableau 2 Directives D’INSTALLATION DE Conduits Étape 2 préparation de découpe du plan de travail Po Plaques de cuisson Installation avec UCVM36FS Po Plaques de cuisson Installation avec UCVM30FSInstallation Avec Autres Plaque DE Cuisson OÙ Spécifié Installation Avec Plaque DE Cuisson Lorsque SpécifiéInstallation Avec Autre Marque DE Plaque DE Cuisson figure 30 po Étape 3 préparer les découpes de conduits dans l’armoireÉtape 6 installation de l’évent et de la plaque de cuisson Étape 5 installation de l’électricitéMount Integral Blower or Outlet Duct Transition for Remote Soufflerie à distance Interrupteur Retirer la pellicule protectrice du dessus de l’embout Instrucciones DE Seguridad Partes que se incluyen Partes que se necesitanIntroducción Paso 1 Planear la instalaciónDescripción General Asegúrese de evitar la interferncia con el Figuras 3 a 6 son ejemplos de posibles ductos Total de ambas columnas= Tabla 2 Lineamente Para LA Instalación DE Ductos Paso 2 Preparar el recorte en la cubierta Parrillas instaladas con UCVM36FS Parrillas instaladas con UCVM30FSCCD COD Instalación CON Parrilla DE Otra Marca Figura Paso 3 Preparar los recortes para los ductos en el gabinete Paso 4 Instalar el ducto ventilador remoto, si se usa Paso 5 Instalar el servicio eléctricoPaso 6 Montar en ventilador y la parrilla Ventilador interno DHZDHR6 Control DE Page Page Noticias 9000 331
Related manuals
Manual 6 pages 62.53 Kb

UCVM30FS, UCVM36FS specifications

The Thermador UCVM36FS is a premium undercounter wine refrigerator designed for wine enthusiasts who demand the finest in preservation technology and aesthetics. With a sleek and modern design, this wine storage unit perfectly blends into any kitchen or entertainment area, providing both functionality and style.

One of the standout features of the UCVM36FS is its capacity to hold up to 36 standard wine bottles. This makes it an ideal choice for wine collectors and social hosts alike, allowing users to store a diverse collection of their favorite vintages. The adjustable shelves are crafted from natural wood, which not only adds a touch of elegance but also helps to cradle bottles and reduce vibration, a key aspect of wine preservation.

Temperature control is critical in wine storage, and the UCVM36FS excels in this area. It offers precise temperature settings, ranging from 4°C to 18°C (39°F to 65°F), ensuring that each type of wine can be stored at its ideal temperature. The dual-zone temperature management technology allows for separate settings for red and white wines, ensuring optimal conditions for both.

Another innovative technology featured in the Thermador UCVM36FS is its advanced cooling system. The unit utilizes a compressor-based cooling system with dynamic cooling technology, which helps maintain a consistent temperature throughout the refrigerator. Additionally, an efficient filtration system protects the wine from external odors and flavors, thus preserving its original taste and quality.

The UCVM36FS also incorporates a no-vibration design. Vibration can disturb sediments in wine, affecting flavor and quality; therefore, Thermador has engineered this model to operate with minimal vibrations. Furthermore, the energy-efficient LED lighting illuminates the interior without generating excess heat, allowing for easy viewing and selection of wines while remaining energy conscious.

A key characteristic of the Thermador UCVM36FS is its customizable design. The unit features a stainless-steel door with a glass panel, offering an elegant display of your wine collection while ensuring UV protection, which shields wines from harmful light exposure. The integrated design allows for a flush installation that enhances the kitchen decor.

In conclusion, the Thermador UCVM36FS undercounter wine refrigerator is equipped with advanced wine preservation technologies, ample capacity, customizable design, and meticulous temperature control, making it a standout choice for discerning wine lovers. Whether for personal enjoyment or entertaining guests, this unit promises to elevate your wine storage experience to new heights.