Alto-Shaam 200-HW/D4, 400-HW/D4, 400-HW/D6, 300-HW/D643, 500-HW/D4, 300-HW/D4 manual N I T a T I O N

Page 16

S A N I T A T I O N

Food flavor and aroma are usually so closely related that it is difficult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food flavor. Cleanliness, top operating efficiency, and appearance of equipment contribute considerably to savory, appetizing foods. Good equipment that is kept clean, works better and lasts longer.

Most food imparts its own particular aroma and many foods also absorb existing odors. Unfortunately, during this absorption there is not distinction between GOOD and BAD odors The majority of objectionable flavors and odors troubling food service operations are caused by bacteria growth. Sourness, rancidity, mustiness, stale or other OFF flavors are usually the result of germ activity.

The easiest way to insure full, natural food flavor is through comprehensive cleanliness. This means good control of both visible soil (dirt) and invisible soil (germs). A through approach to sanitation will provide essential cleanliness. It will assure an attractive

appearance of equipment, along with maximum efficiency and utility. More importantly, a good sanitation program provides one of the key elements in the prevention of food-borne illnesses.

A controlled holding environment for prepared foods is just one of the important factors involved in the prevention of food-borne illnesses. Temperature monitoring and control during receiving, storage, preparation, and the service of foods are of equal importance.

The most accurate method of measuring safe temperatures of both hot and cold foods is by internal product temperature. A quality thermometer is an effective tool for this purpose, and should be routinely used on all products that require holding at a specific temperature.

A comprehensive sanitation program should focus on the training of staff in basic sanitation procedures. This includes personal hygiene, proper handling of raw foods, cooking to a safe internal product temperature, nd the routine monitoring of internal temperatures from receiving through service.

Most food-borne illnesses can be prevented through proper temperature control and a comprehensive program of sanitation. Both these factors are important to build quality service as the foundation of customer satisfaction. Safe food handling practices to prevent food- borne illness is of critical importance to the health and safety of your customers.

HACCP, an acronym for Hazard Analysis (at) Critical Control Points, is a quality control program of operating procedures to assure food integrity, quality, and safety. Taking steps necessary to augment food safety practices is both cost effective and relatively simple. While HACCP guidelines go far beyond the scope of this manual, additional information is available by contacting:

CENTER FOR FOOD SAFETY AND APPLIED

NUTRITION FOOD AND DRUG ADMINISTRATION

1-888-SAFEFOOD

INTERNAL FOOD PRODUCT TEMPERATURES

H OT FOOD S

DANGER ZONE

40° TO 140°F

(4° TO 60°C)

CRITICAL ZONE

70° TO 120°F

(21° TO 49°C)

SAFE ZONE

140° TO 165°F

(60° TO 74°C)

 

COLD FOOD S

 

DANGER ZONE

ABOVE 40°F

(ABOVE 4°C)

SAFE ZONE

36° TO 40°F

(2° TO 4°C)

 

FROZEN FOOD S

 

DANGER ZONE

ABOVE 32°F

(ABOVE 0°C)

CRITICAL ZONE

0° TO 32°F

(-18° TO 0°C)

SAFE ZONE

0°F or below

(-18°C or below)

Hot Food Drop-In Well Operation & Care Manual • 14

Image 16
Contents Installation Operating Instructions L I V E R Y P a C K I N GSafety Procedures Precautions Safe operation of electrically and/or gas energizedInstallation Options and AccessoriesLeveling Rough CUT Counter TOP OpeningElectrical Connection E C T R I C a L Specifications Refer to wire diagram sent with unitRemote Control Housing Mounting Instructions Dimensions Capacity 100-HW/D4 & 100-HW/D6 HW/D4300-HW/D4, D6, D443, D643 500-HW/D4 & 500-HW/D6 Reset Thermostats AS Needed Operating InstructionsDo not ADD Water to HOT Well Place PAN Dividers and Empty Pans in the WellsGeneral Holding Guidelines Halo Heat maintains the maximum amount of productCleaning and Preventive Maintenance Cleaning AgentsCleaning Materials Protecting Stainless Steel SurfacesCare and Cleaning Clean the Appliance DailyWarranty Becomes Void if Appliance is Flooded Interior Severe Damage or Electrical Hazard Could ResultN I T a T I O N R V I C E Service PartsTools Required 2mm allen hex wrench Hot Food Drop-In Well Operation & Care Manual Hot Food Drop-In Well Operation & Care Manual Hot Food Drop-In Well Operation & Care Manual Hot Food Drop-In Well Operation & Care Manual Hot Food Drop-In Well Operation & Care Manual Transportation Damage and Claims Voltage Purchased From