Denon AVR-682 manual Connections, Connecting the audio components, Use them for hair driers, etc

			ENGLISH
8	CONNECTIONS
•	Do not plug in the power cord until all connections have been	• Note that binding pin plug cords together with power cords or
	completed.	placing them near a power transformer will result in generating
•	Be sure to connect the left and right channels properly (left with	hum or other noise.
	left, right with right).	• Noise or humming may be generated if a connected audio
•	Insert the plugs securely. Incomplete connections will result in	equipment is used independently without turning the power
•	the generation of noise.	of this unit on. If this happens, turn on the power of the this
	Use the AC OUTLETS for audio equipment only. Do not	unit.
	use them for hair driers, etc.

Connecting the audio components

Decoders with 6-channel
analog outputs, etc.
LINE OUT	SUBWOOFER	CENTER
SURROUND			R	L
			FRONT

AC CORD

AC 120V, 60Hz

			AUDIO		DIGITAL	PRE OUT
		R	L	IN	IN
		AM		CD		SUB
	LOOP					WOOFER
	ANT.
				DVD/		DVD/
				VDP		VDP
		FM				IN
				TV/		TV/
		COAX.			COAXIAL
				DBS		DBS
	R	75
	ANTENNA			VCR		VCR
	FR	FL		CDR/	OPTICAL	MONITOR
				TAPE
L	SW	C		VCR		VCR
R	SR	SL		CDR/	OPTICAL
				TAPE		OUT
	EXT. IN			OUT	OUT	VIDEO

R L R L

IN						OUT
DVD/	TV/	VCR	MONITOR		VCR
VDP	DBS
		S-VIDEO
					SPEAKER SYSTEMS
	B	FRONT			A		CENTER	SURROUND
				R		L		R	L
R		L
		SPEAKER IMPEDANCE					CENTER	/ 6	16
		FRONT		A OR B / 6		16
				A +	B / 6	16	SURROUND / 6		16

Subwoofer jack

AC OUTLETS

AC 120V 60Hz

SWITCHED

TOTAL 120W(1A.) MAX.

LINE IN

LINE OUT

Tape deck or CD recorder

R L R L

R L R L

INPUT OUTPUT

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape recording (OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape playback (IN) jacks using pin plug cords.

CD recorder, MD recorder or other component
equipped with digital output lacks.	IN	OUT
OPTICAL
B
OUTPUT INPUT	LINE	LINE

DIGITAL jacks

Use these for connections to audio equipment with digital output. Refer to Page 20 for instructions on setting this terminal.

•Use 75 Ω /ohms cable pin cords (sold separately) for coaxial connections.

•Use optical cables (sold separately) for optical connections.

Connect the internal amplifier’s subwoofer to the subwoofer terminal. (Refer to page 13.)

Connecting the AC OUTLETS

AC OUTLETS

• SWITCHED

(total capacity – 120 W (1 A.))

The power to these outlets is turned on and off in conjunction with the POWER switch on the main unit, and when the power is switched between on and standby from the remote control unit.

No power is supplied from these outlets when this unit’s power is at standby. Never connect equipment whose total capacity is above 120 W (1 A.)

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or other electrical appliances.

OUTPUT		CD player	Connecting a CD player
R	L
			Connect the CD player’s analog
R	L		output jacks (ANALOG OUTPUT) to
			this unit’s CD jacks using pin plug
			cords.

LINE OUT

9