Lennox Hearth Manufactured Mobile Home Installation, Model - T300P SERIES, Check list

Page 7
INSTALLATION

INSTALLATION

MANUFACTURED (MOBILE) HOME INSTALLATION

Model –T300P Series

In addition to the standard installation instructions, the following instructions may be required by local, state or federal building codes:

Stove must be permanently bolted to the floor.

An outside air inlet must be provided for combustion and be unrestricted while unit is in use.

Stove must be permanently electrically grounded to the steel chassis of the home. The location selected for ground attachment to the stove must be dedicated for this purpose.

See pages 10 through 15 for additional information on venting requirements.

Do not install appliance in a sleeping room.

The structural integrity of the manufactured home floor, walls, ceiling and roof must be maintained.

NOTE: The grounding of this product, at installation, must comply with NFPA-70 standards, CSA C22.1 in Canada, as well as any local codes.

Model - T300P SERIES

Chassis

Floor

Bolt Floor

Protector

MANUFACTURED (MOBILE) HOME EXHAUST VENT PIPE INSTALLATION GUIDELINES

Use only listed type “PL” pellet vent pipe. Pipe should extend at least 3 feet above the part of the roof through which it passes. The top of the pipe should be at least 2 feet above the highest required elevation of any part of the manufactured (mobile) home within 10 feet of the pipe.

If the exhaust vent exits the manufactured (mobile) home at a location other than the roof, and exits at a point 7 feet or less above the ground level on which the manufactured (mobile) home is position a guard or method of enclosing the pipe shall be provided at the point of exit for a height of up to 7 feet. The openings, if any, in this guard shall not allow a 3/4” rod to pass through. A 1/2” rod could pass through but should not be able to touch the pipe when inserted through the opening a distance of 4 inches.

Page 7

REMOVING APPLIANCE FROM PALLET

1.After removing the packaging from the stove, lift the hopper lid, and remove all pre-packaged items that were shipped in the hopper. Next, open the stove door and remove all pre-packaged items.

2.Remove screws which secure legs to pallet.

INSTALLING LEG LEVELING BOLTS

The four leg leveling bolts (included in accessory pack- age), are provided for leveling the stove if necessary. To install, thread the bolts into the existing holes in the bottom of each leg. Turn the leveling bolts to adjust for correct height.

INSTALLATION CHECK LIST

It is strongly recommended that you have an authorized Lennox Hearth Products dealer install your stove. If you install your stove yourself, you should review your in- stallation plan with your authorized Lennox Hearth Products dealer.

Check list:

Check off each item as you proceed with the installation process.

Read the ENTIRE stove installation section first. Determine the appropriate measurements and loca- tions for your installation.

Follow the general installation directions under Stove Installation and the installation section ap- propriate to your stove.

Be sure to pre-fit all items before you install, fasten, or set up the stove permanently.

Prior to lighting your stove:

Review the safety precaution section. Review the pellet fuels section.

Review and follow the Operating Instructions.

Plug power cord connector into corresponding con- nector on the back of appliance (see illustration on page 9 showing connector locations).

After you have begun operation of your stove: Review the routine cleaning / maintenance informa- tion.

Enjoy the warmth from your new Lennox Hearth Products pellet stove!

Image 7
Contents FREESTANDING PELLET FIRED STOVES Freestanding Model T300P SeriesRETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE IMPORTANT WARNINGS TABLE OF CONTENTS PLANNING YOUR INSTALLATION T300P SERIES FLOOR PROTECTIONCLEARANCES INSTALLATION CHECK LIST INSTALLATIONMANUFACTURED MOBILE HOME INSTALLATION INSTALLING LEG LEVELING BOLTSFig. A DAMPER ROD INSTALLATIONDAMPER ADJUSTMENT Pulled Back 3 NotchesRemove Jumper if Thermostat IsTo Be Used THERMOSTAT INSTALLATIONTerminal Block for Thermostat Leave Jumper on, If Thermostat Is NotUsedVENTING REQUIREMENTS Chimney Height Requirements VENT TERMINATIONManufactured Mobile Home DETERMINING SIZE OF PIPE TO INSTALL INSTALLING YOUR PELLET STOVE Page Installation Configurations / Standard Venting Options This appliance may be connected to an existing flue or by installing listed type “PL” vent pipe. If a liner is run all the way to the top of the existing chimney, the existing flue should be sealed with a steel plate. Start a vertical run with a Tee at the back of the stove. Other options are illustrated below. Note See page 11 for Vent Termi- nation Requirements CONTROL BOARD OPERATION CARE AND OPERATIONStart-upSequence of Events Fuel Delivery Rate Combustion Voltage Trim StepsTurning Off Your Stove Lighting Procedure Without IgniterManual Operation Automatic OperationOverheating DAMPER ADJUSTMENT GUIDELINEAUTOMATIC SAFETY FEATURES Power Outage DAMPER OPERATIONCLINKERING FUEL REQUIREMENTSPellet Feed / Pellet Size Long Burn TimeAsh Pan ROUTINE MAINTENANCEROUTINE CLEANING ASH PANClean-OutTee Remove Filter and Wipe Clean Photoeye Access Inside HopperAnnual Maintenance Procedure Clean Photoeye Lens Clean Filter LensTube Scraper Clean-OutTee w/ Cover RemovedRemove cover, then remove ash HEAT EXCHANGER TUBESDOOR ROPE GASKET SPECIFICATIONS - Model T300P Series DEFINITIONS WIRING DIAGRAM CAUSES TROUBLESHOOTING Qualified Technicians OnlyPROBLEM SOLUTIONS4. Blowers will REPLACEMENT PARTS LIST Misc. Parts AugerREPLACEMENT PARTS DIAGRAMS 14 20 15 Model # OPTIONAL ACCESSORIESOptional Accessories Catalog #INSTALLATION TIPS SIMPLE OPERATING INSTRUCTIONS LABEL T300P PELLET STOVE SAFETY LABEL SERVICE AND MAINTENANCE LOG 1110 West Taft Avenue Orange, CA