Rangemaster U109948 - 04 manual Completing the Move, Repositioning the Cooker following Connection

Page 22

Fig.7-6

����

ArtNo.010-0008 Lowering the front rollers

Fig.7-7

ArtNo.010-0002 Rear roller nut

Fig.7- 8

ArtNo.010-0003 Lowering the rear rollers

x10

Fig.7-9

ArtNo.010-0009 Pushing the cooker

Fig.7-10

ArtNo.010-0004 Moving the cooker

LOWER THE FRONT ROLLER by doing 14 complete (360°) turns clockwise (Fig.7-6). (This means turning and removing the levelling tool 56 times).

Now LOWER THE TWO REAR ROLLERS. First fit the levelling tool on the hexagonal adjusting nut (Fig.7-7). Make 10 complete (360º) turns clockwise (Fig.7-8). (This means turning and removing the levelling tool 20 times.)

Make sure you lower BOTH REAR ROLLERS. There are two adjusting nuts, one for each roller, at both the front bottom corners of the cooker.

Unfold the rear edge of pack base tray. Carefully push the cooker backwards out of the base pack (Fig.7-9). Push the cooker close to its final position, leaving just enough space to get behind it.

Completing the Move

Unfold the rear edge of the pack base tray. Open the grill door and right hand oven door so that you can get a good grip on the bottom of the fascia panel as you move the cooker.

Grip under the fascia panel and lift the front of the cooker slightly (Fig.7-10). Carefully push the cooker backwards off the pack base. Remove the pack base tray. Position the cooker close to its final position, leaving just enough space to get behind it.

DO NOT use the door handles or control knobs to manoeuvre the cooker.

Repositioning the Cooker following Connection

If you need to move the cooker once it has been connected, make sure it is switched off at the supply switch before gripping under the fascia panel and lifting the front of the cooker slightly (Fig.7-10). Check behind the cooker to ensure that the electricity cable is not caught. As you progress, always ensure that the cable has sufficient slack to allow the cooker to move.

If a stability chain is fitted, release it as you ease the cooker out. Do not forget to refit it when you replace the cooker.

When you replace the cooker, check behind it again once more to ensure that the electricity cable is not caught or trapped.

Levelling

It is recommended that you use a spirit level on a shelf in one of the ovens to check for level.

Place the cooker in its intended position, taking care not to twist it within the gap between the kitchen units as damage may occur to the cooker or the units.

The rollers can be adjusted to level the cooker. To adjust the height of the rear of the cooker, use the levelling tool supplied to turn the adjusting nuts at the front bottom corners of the cooker.

Adjust the height of the front roller to level the cooker. Turn

20

Page 21 Page 23
Image 22
Page 21 Page 23
Contents User Guide Contents Before You Start Personal SafetyInstallation and Maintenance VentilationCooker Care CleaningHob Care  do not use the hob surface as a cutting boardCooker Overview HobPan Detector Residual Heat Indicator, HAutomatic Heat-up, a Child Lock, L GrillBoil Dry Function Left-Hand Oven  Never close the grill door when the grill is onOvens Right-Hand OvenClock Setting the time of daySetting the minute minder To stop the right-hand oven automaticallyAuto is showing, you want to reset to manual cooking Key LockOven Shelves AccessoriesHandyrack Browning Element Main Oven LightStorage Cooking Tips Tips on Cooking with the TimerGeneral Oven Tips Cooking Table MeatCleaning Burned-on Spills Cleaning Your CookerCleaning Spills Daily CareTo Remove Metal Rub-off Control Panel and DoorsDoor Panel  do not use any abrasive substances‘Cook & Clean’ Panels Removing the Panels to clean the Enamel InteriorTroubleshooting Oven temperature getting hotter as the cooker gets older Timed oven is not coming on when turned on manuallyTimed oven is not coming on when automatic cooking Food is cooking too slowly, too quickly, or burningSafety Requirements InstallationDear Installer Provision of VentilationUnpacking the Cooker Positioning the CookerMoving the Cooker Repositioning the Cooker following Connection Completing the MoveLevelling Grill Check Electrical ConnectionHob Check Oven CheckTo Remove the Control Panel ServicingTo Lift up the Ceramic Hob To Replace a Hob ElementTo Replace a Thermostat To Remove the Electronic TimerTo Remove the Grill Door To Remove the Grill Element To Adjust an Oven Door AngleTo Replace the Grill Controller To Replace an Oven DoorTo Remove an Oven Element Thermal Cut-out To Adjust an Oven Door Catch KeepTo Replace an Oven Door Seal To Remove an Oven Inner BackTo Remove the Left-hand Oven Bottom and Top Elements To Replace an Oven FanTo Change Oven Light Bulb Circuit Diagram Oven Key3kW 4kW Circuit Diagram Hob3kW2.3kW 4kW Dimensions Technical DataConnections DocNo.000-0001 Back cover Rangemaster
Top Page Image Contents