Rangemaster U109948 - 04 manual To Replace the Grill Controller, To Remove the Grill Element

Page 26

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have finished.

Fig.8-4

ArtNo.320-0006 Oven door hinge adjustment 1

Effect of hinge adjustment - exagerrated for clarity

Note: The arms are spring tensioned. Carefully remove the grill door. Retain the gaskets.

Reassemble in reverse order ensuring that the gasket is fitted between the hinge arm and the front of the grill chamber.

9.To Replace the Grill Controller

Disconnect from electricity supply.

Lift up the hob (see 2) and remove the control panel (see 3). Disconnect the wiring from the controller. Remove the two screws holding the controller to the mounting panel. Fit the new controller and reassemble in reverse order. Check for correct operation.

Fig.8-5

Centreline of hinge pin

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

Fig.8-6

ArtNo.320-0002a Proplus oven door side screws

10.To Remove the Grill Element

Disconnect from electricity supply.

Remove grill pan from inside the grill compartment; remove the enamelled front shield from the grill roof, by undoing the two screws and washers.

Remove the two screws and washers securing the grill element front support. Remove the screws from the grill element.

Lift the element out carefully, disconnecting the leads from the element terminals (noting their position). If it is not possible to disconnect the leads in this way, pull the cooker forward to gain access to the rear, remove the screws securing the electric cover to the back sheet, remove the cover and disconnect the terminals from the rear.

Fit the new element and reassemble in reverse order. Check the operation of the grill.

11.To Replace an Oven Door

Open the oven door. Support the door and remove the two screws securing the upper hinge and gasket to the cooker front (Fig.8-2). Remove the door from the lower hinge by lifting slightly and moving outwards (Fig.8-3).

The door is heavy, so take care.

Reassemble in reverse order.

12.To Adjust an Oven Door Angle

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig.8-4). Loosen the bottom hinge fixing screws and use the notch and a flat bladed screwdriver to move the position of the hinge to set the hinge position (Fig.8-5).

Retighten the hinge screws.

13.To Replace an Oven Door Outer Panel

Move the cooker forward to gain access to the sides.

Open the oven door slightly and remove the front panel fixing screws from the door sides – two each side (Fig.8-6).

Carefully lift off the outer door panel.

Remove the door handle from the panel by unscrewing the two retaining nuts. Fit the door handle to the new panel.

Fit the panel to the door. Reassemble in reverse order.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents User Guide Contents Before You Start Personal SafetyInstallation and Maintenance VentilationCooker Care CleaningHob Care  do not use the hob surface as a cutting boardCooker Overview HobAutomatic Heat-up, a Residual Heat Indicator, HPan Detector Boil Dry Function GrillChild Lock, L Left-Hand Oven  Never close the grill door when the grill is onOvens Right-Hand OvenClock Setting the time of daySetting the minute minder To stop the right-hand oven automaticallyAuto is showing, you want to reset to manual cooking Key LockHandyrack AccessoriesOven Shelves Storage Main Oven LightBrowning Element General Oven Tips Tips on Cooking with the TimerCooking Tips Cooking Table MeatCleaning Burned-on Spills Cleaning Your CookerCleaning Spills Daily CareTo Remove Metal Rub-off Control Panel and DoorsDoor Panel  do not use any abrasive substances‘Cook & Clean’ Panels Removing the Panels to clean the Enamel InteriorTroubleshooting Oven temperature getting hotter as the cooker gets older Timed oven is not coming on when turned on manuallyTimed oven is not coming on when automatic cooking Food is cooking too slowly, too quickly, or burningSafety Requirements InstallationDear Installer Provision of VentilationMoving the Cooker Positioning the CookerUnpacking the Cooker Levelling Completing the MoveRepositioning the Cooker following Connection Grill Check Electrical ConnectionHob Check Oven CheckTo Remove the Control Panel ServicingTo Lift up the Ceramic Hob To Replace a Hob ElementTo Remove the Grill Door To Remove the Electronic TimerTo Replace a Thermostat To Remove the Grill Element To Adjust an Oven Door AngleTo Replace the Grill Controller To Replace an Oven DoorTo Remove an Oven Element Thermal Cut-out To Adjust an Oven Door Catch KeepTo Replace an Oven Door Seal To Remove an Oven Inner BackTo Change Oven Light Bulb To Replace an Oven FanTo Remove the Left-hand Oven Bottom and Top Elements Circuit Diagram Oven Key3kW2.3kW 4kW Circuit Diagram Hob3kW 4kW Connections Technical DataDimensions DocNo.000-0001 Back cover Rangemaster
Top Page Image Contents