Rangemaster U109948 - 04 manual Electrical Connection, Hob Check, Grill Check, Oven Check

Page 23

clockwise to raise the cooker and anticlockwise to lower.

When you are satisfied with the height and level, raise the front of the cooker by one turn of the front roller adjuster. Screw down the front feet to meet the floor. Screw the front roller adjuster anticlockwise to raise the front roller so that the front of the cooker is supported on the feet, not the front roller, to prevent accidental movement of the cooker.

Leave the levelling tool on the adjuster with the handle of the tool facing the rear of the cooker, so that the customer can use it if they wish to move the cooker.

Replace the drawer by locating it on the side runners and pushing in.

Electrical Connection

The cooker must be installed by a qualified electrician, in accordance with all relevant British Standards/Codes of Practice (in particular BS 7671), or with the relevant national and local regulations.

WARNING: THE APPLIANCE MUST BE EARTHED.

Note: The cooker must be connected to the correct electrical supply as stated on the voltage label on the cooker, through a suitable cooker control unit incorporating a double pole switch, having a contact separation of at least 3mm in all poles.

The cooker must not be connected to an ordinary domestic power point.

Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type (Fig.7-11and Fig.7-12). Check that the links are correctly fitted and that the terminal screws are tight. Secure the mains cable using the cable clamp.

Fig.7-11

�����

���

ArtNo.130-0010 Electrical connections single-phase

������������

Fig.7-12

��

��

��

����

 

 

���

�����

���

�����ArtNo.130-0010 Electrical connections 3-phase

�������������

Fig.7-13

Hob Check

Check each cooking zone in turn. Be sure to use pans of the correct size and material.

ArtNo.000-0006 - Securing the 110 plinth

Grill Check

Turn on the grill control and check that the grill heats up.

Oven Check

Set the clock as described earlier, and then turn on the ovens.

Check the oven fans start to turn and that the ovens heat up.

Fitting the Plinth

Loosen the three screws along the front bottom edge of the cooker. Hook the central keyhole over the central screw. Twist and fit each end keyhole over their respective screws. Tighten the fixing screws (Fig.7-13).

Please complete your contact details in the front of this section. Please inform the user how to operate the cooker and hand over the instruction pack.

Thank you.

21

Image 23
Contents User Guide Contents Ventilation Personal SafetyInstallation and Maintenance Before You Start do not use the hob surface as a cutting board CleaningHob Care Cooker CareHob Cooker OverviewAutomatic Heat-up, a Residual Heat Indicator, HPan Detector Boil Dry Function GrillChild Lock, L Right-Hand Oven  Never close the grill door when the grill is onOvens Left-Hand OvenTo stop the right-hand oven automatically Setting the time of daySetting the minute minder ClockKey Lock Auto is showing, you want to reset to manual cookingHandyrack AccessoriesOven Shelves Storage Main Oven LightBrowning Element General Oven Tips Tips on Cooking with the TimerCooking Tips Meat Cooking TableDaily Care Cleaning Your CookerCleaning Spills Cleaning Burned-on Spills do not use any abrasive substances Control Panel and DoorsDoor Panel To Remove Metal Rub-offRemoving the Panels to clean the Enamel Interior ‘Cook & Clean’ PanelsTroubleshooting Food is cooking too slowly, too quickly, or burning Timed oven is not coming on when turned on manuallyTimed oven is not coming on when automatic cooking Oven temperature getting hotter as the cooker gets olderProvision of Ventilation InstallationDear Installer Safety RequirementsMoving the Cooker Positioning the CookerUnpacking the Cooker Levelling Completing the MoveRepositioning the Cooker following Connection Oven Check Electrical ConnectionHob Check Grill CheckTo Replace a Hob Element ServicingTo Lift up the Ceramic Hob To Remove the Control PanelTo Remove the Grill Door To Remove the Electronic TimerTo Replace a Thermostat To Replace an Oven Door To Adjust an Oven Door AngleTo Replace the Grill Controller To Remove the Grill ElementTo Remove an Oven Inner Back To Adjust an Oven Door Catch KeepTo Replace an Oven Door Seal To Remove an Oven Element Thermal Cut-outTo Change Oven Light Bulb To Replace an Oven FanTo Remove the Left-hand Oven Bottom and Top Elements Key Circuit Diagram Oven3kW2.3kW 4kW Circuit Diagram Hob3kW 4kW Connections Technical DataDimensions DocNo.000-0001 Back cover Rangemaster