Rangemaster U109948 - 04 manual Servicing, To Lift up the Ceramic Hob, To Remove the Control Panel

Page 24

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have finished.

8. Servicing

Fig.8-1

ArtNo.210-0008 - Classic Removing the end caps

Disconnect the cooker from the electricity supply before servicing, particularly before removing any of the following: control panel, side panels, ceramic hob, or any of the electrical components or cover boxes.

Before reconnection, check that the appliance is electrically safe.

1.To Remove a Side Panel

Disconnect from electricity supply.

Pull the cooker forward. Pull off the control panel end caps at each end of the panel (Fig.8-1). Remove the fixing screws under the end caps.

Remove the retaining screws for each panel (one at the front, two at the rear, and one at each lower front corner of the side panels).

Reassemble in reverse order.

2.To Lift up the Ceramic Hob

Disconnect from electricity supply.

Remove the side panels (see 1) to allow access to the hob fixing screws (1 each side) at the top of the side uprights. Remove these screws.

Lift up the ceramic hob at the front and prop in position with a non-metallic prop.

CAUTION: The ceramic hob material is much more sensitive to scratches on the underside than the top.

Take care not to touch or scratch the underside of the ceramic as this will weaken the material and cause the top to shatter.

3.To Remove the Control Panel

Disconnect from electricity supply.

Pull off the control panel end caps at each end of the panel (Fig.8-1). Remove the fixing screws under the end caps.

Pull off all the control knobs. Open the grill and right-hand oven door and remove the control panel fixing screws underneath the control panel. The screws directly below the clock are for the clock fixing bracket, so do not remove them at this stage.

Lift the control panel, pull forward and disconnect the wiring from the rear.

Reassemble in reverse order. When replacing leads, refer to the wiring diagram in this manual. Check the operation of the timer.

4.To Replace a Hob Element

Disconnect from electricity supply.

Lift up the ceramic hob (see 2). The Induction Heating Elements (IHE) are now accessible. Note the wire connection positions and element orientation for re-assembly. Disconnect the wires, and remove the element unit and springs. Re- assemble in the reverse order.

Note: The IHE will require commissioning when the hob has been refitted.

22

Page 23 Page 25
Image 24
Page 23 Page 25
Contents User Guide Contents Personal Safety Installation and MaintenanceBefore You Start VentilationCleaning Hob CareCooker Care  do not use the hob surface as a cutting boardCooker Overview HobResidual Heat Indicator, H Pan DetectorAutomatic Heat-up, a Grill Child Lock, LBoil Dry Function  Never close the grill door when the grill is on OvensLeft-Hand Oven Right-Hand OvenSetting the time of day Setting the minute minderClock To stop the right-hand oven automaticallyAuto is showing, you want to reset to manual cooking Key LockAccessories Oven ShelvesHandyrack Main Oven Light Browning ElementStorage Tips on Cooking with the Timer Cooking TipsGeneral Oven Tips Cooking Table MeatCleaning Your Cooker Cleaning SpillsCleaning Burned-on Spills Daily CareControl Panel and Doors Door PanelTo Remove Metal Rub-off  do not use any abrasive substances‘Cook & Clean’ Panels Removing the Panels to clean the Enamel InteriorTroubleshooting Timed oven is not coming on when turned on manually Timed oven is not coming on when automatic cookingOven temperature getting hotter as the cooker gets older Food is cooking too slowly, too quickly, or burningInstallation Dear InstallerSafety Requirements Provision of VentilationPositioning the Cooker Unpacking the CookerMoving the Cooker Completing the Move Repositioning the Cooker following ConnectionLevelling Electrical Connection Hob CheckGrill Check Oven CheckServicing To Lift up the Ceramic HobTo Remove the Control Panel To Replace a Hob ElementTo Remove the Electronic Timer To Replace a ThermostatTo Remove the Grill Door To Adjust an Oven Door Angle To Replace the Grill ControllerTo Remove the Grill Element To Replace an Oven DoorTo Adjust an Oven Door Catch Keep To Replace an Oven Door SealTo Remove an Oven Element Thermal Cut-out To Remove an Oven Inner BackTo Replace an Oven Fan To Remove the Left-hand Oven Bottom and Top ElementsTo Change Oven Light Bulb Circuit Diagram Oven KeyCircuit Diagram Hob 3kW 4kW3kW2.3kW 4kW Technical Data DimensionsConnections DocNo.000-0001 Back cover Rangemaster
Top Page Image Contents