Smeg SE2642ID3 manual Technical information, Rating plate, Electrical connection, HOB Rating

Page 25

 

 

Instructions for the installer

 

11.8 Technical information

Hob model

See rating plate

Electrical connections

220-240V~ 50/60Hz / 380-415V 2N~ 50/60Hz

HOB RATING

I

Maximum power

See rating plate

11.9 The rating plate

Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason.

11.10 Electrical connection

The electrical connection of the hob must be installed by an authorised technician.

The applicable legislation and rules for connection to the local electricity supplier must be followed.

Disconnect the appliance from the power supply, using one of these devices, when you want to connect it to the supply or carry out repairs.

The earthing wire must be longer than the current conduction wires so that, if the plug is torn off the power cable, it is the last to be detached.

Surplus parts of the cable must be taken out of the installation area under the appliance.

• To make the connection, the control cover underneath the device must be loosened so that the terminal board can be reached. Once the connection has been made, the cover must be fixed back in place and the cable must be locked using a traction-resistant clamp.

The connection cable must correspond to type H05 V2V2-F

as a minimum.

If the appliance connection cable is damaged, it must be

replaced by the manufacturer, their Technical Support Service or a qualified technician to avoid any danger.

• When the appliance has been installed, it must be protected from accidental contact with the electric cables.

Warning! The electronic controls could be damaged beyond repair if the connection is not professionally carried out.

IT IS OBLIGATORY FOR ALL ELECTRICAL EQUIPMENT TO BE EARTHED ACCORDING TO THE METHODS LAID DOWN BY SAFETY REGULATIONS.

WHERE THE APPLIANCE IS CONNECTED TO THE POWER GRID VIA A PLUG AND SOCKET, BOTH OF THESE MUST BE OF THE SAME TYPE AND CONNECTED TO THE POWER CABLE IN ACCORDANCE WITH THE APPLICABLE REGULATIONS.

THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE IS INSTALLED. NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE APPLIANCE FOLLOWING THE INSTRUCTIONS PROVIDED EARLIER IN THIS MANUAL. IF IT DOES NOT FUNCTION CORRECTLY, AFTER HAVING ENSURED THAT THE INSTRUCTIONS HAVE BEEN PROPERLY FOLLOWED, DISCONNECT THE APPLIANCE FROM THE POWER SUPPLY AND CALL THE NEAREST TECHNICAL SUPPORT CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

RUN THE POWER CABLE UNDER THE UNIT, TAKING CARE THAT IT DOES NOT COME INTO CONTACT WITH THE BOTTOM OF THE CASING OF THE HOB OR THE OVEN BENEATH IT IF THERE IS ONE.

IF A PLUG AND SOCKET CONNECTION IS USED, CHECK THAT THEY ARE THE SAME TYPE. DO NOT USE ANY TYPE OF ADAPTOR OR DIVERTER AS THESE MAY CAUSE OVERHEATING OR BURNS.

WHERE A FIXED CONNECTION IS IN USE, A MULTIPOLAR CUT-OUT DEVICE MUST BE INSTALLED ON THE SUPPLY CABLE WITH A CONTACT OPENING DISTANCE EQUAL OR GREATER THAN 3 MM, LOCATED IN A READILY REACHABLE POSITION NEAR THE APPLIANCE.

53

Image 25
Contents Contents Plate Must not be Removed Instructions for USEInformation for Users Recycling Instructions OUR Environment PolicyAuthorised Technician or AT AN Authorised Service Centre Safety InstructionsPlease note Safety instructions Intended USE of the Appliance Before First USESaucepan recognition HobOther functions Limitation on the duration of useProtection from overheating induction Saucepans suitable for use in induction cookingPower levels Advice on energy-savingCooking zones Residual heat indicatorControl panel Cooking zone selector button Using the SensorsOperating power settings Using the HOBMAX Absorbed Power Absorbed Power Power FunctionSwitching off the cooking zone Switching on the hob and the cooking zoneSwitching off the hob Stop functionActivating the child lock Automatic switch-off timerQuick start cooking Timer clockPower function cooking zone with P Plate warmer function where applicableSetting Type of Food Power managementCooking guidelines Cleaning the glass ceramic hob Cleaning and MaintenanceWeekly cleaning Never Steam Clean the ApplianceProblem Possible Causes Solution TROUBLE-SHOOTINGInstructions for the User Safety instructions for installing kitchen furniture InstallationVentilation PositioningSection cut from the work surface Hob sealInserting the hob into the hole in the work surface Positioning the fastening clipsRating plate Technical informationElectrical connection HOB RatingInstructions for the installer