Taylor model 430 torque shake/slush freezer Air Cooled Units, Electrical Connections, 130930

Page 6

Air Cooled Units

DO NOT obstruct air intake and discharge openings: Air cooled units require a minimum of 3” (76.2 mm) of clearance around all sides of the freezer to allow for adequate air flow across condenser. Failure to allow adequate clearance can reduce the refrigeration capacity of the freezer and possibly cause permanent damage to the compressor.

Electrical Connections

This equipment is supplied with a 3- wire cord and grounding type plug, for connection to a single phase, 60 cycle, branch circuit supply. This unit must be plugged into a properly grounded receptacle. The cord and plug provided are 20A for 115/60/1 or 15A for 208- 230/60/1; therefore, the wall outlet must also be 20A for 115/60/1 or 15A for 208- 230/60/1. Check the data label, located on the side panel, for electrical specifications. Permanent wiring may be employed, if required by local codes. Instructions for conversion to permanent wiring are as follows:

1.Be sure the freezer is electrically disconnected.

2.Remove the appropriate panel and locate the small electrical box at the base of the freezer.

3.Remove the factory installed cord and strain relief bushing.

4.Route incoming permanent wiring through 7/8” (22 mm) hole in base pan.

5.Connect two power supply leads. Attach ground (earth) wire to the grounding lug inside the electrical box.

6.Be sure unit is properly grounded before applying power.

In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70-1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety. In all other areas of the world, equipment should be installed in accordance with the existing local codes. Please contact your local authorities.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

130930

Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and other electrical specifications. Refer to the wiring diagram provided inside of the electrical box for proper power connections.

CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK!

This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment’s frame.

SStationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation.

SAppliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected, not used for long periods, or during initial installation, shall have protective devices such as a GFI to protect against the leakage of current, installed by authorized personnel to the local codes.

SSupply cords used with this unit shall be oil-resistant, sheathed flexible cable, not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion.

If the supply cord is damaged, it must be replaced by an authorized Taylor service technician in order to avoid a hazard.

To the Installer

2

Model 430 Torque

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operators Manual Information found on data plate Table of Contents Table of Contents Section Installer SafetyModel 430 Torque To the Installer Site PreparationElectrical Connections To the Installer Model 430 TorqueAir Cooled Units 130930Beater Rotation Refrigerant130816 To the Operator 131202 To the Operator Model 430 TorqueSection Safety Model 430 Torque Safety130930 Safety Model 430 Torque 070104 Operator Parts IdentificationDescription Part Number Model 430 Torque Operator Parts Identification130816 Operator Parts Identification Model 430 Torque 140102 Section Important To the Operator Model 430 Torque Operating Procedures Section Operating ProceduresAssembly StepOperating Procedures Model 430 Torque Step 090114 Operating Procedures Model 430 Torque SanitizingPriming 140804Draining Product From The Freezing Cylinder Closing Procedure140804 Operating Procedures Model 430 Torque RinsingBrush Cleaning CleaningDisassembly 090114 Model 430 Torque Operating ProceduresRegular Maintenance Checks Important Operator ChecklistDuring Cleaning and Sanitizing 071205 Important Operator Checklist Model 430 TorqueModel 430 Torque Important Operator Checklist Winter StorageSection Troubleshooting Guide Troubleshooting Guide Model 430 TorqueModel 430 Torque Troubleshooting Guide Parts Replacement Schedule Parts Replacement Schedule Model 430 TorqueFrozen Yogurt Product Part Limited Warranty Period Soft ServeModel 430 Torque Limited Warranty on Equipment ShakesLimited Warranty on Equipment Model 430 Torque Part’s Warranty Class Code or Part Limited Warranty Period Model 430 Torque Limited Warranty on PartsLimited Warranty on Parts Model 430 Torque Taylor Company Torque Company 430Torque

model 430 torque shake/slush freezer specifications

The Taylor Model 430 Torque Shake/Slush Freezer is a versatile machine that stands out in the world of foodservice equipment, particularly in the realm of frozen desserts and beverages. This innovative machine is designed to offer high-quality slush and shake production, making it an essential addition to restaurants, cafes, and mobile vending operations.

One of the main features of the Taylor Model 430 is its ability to produce a variety of frozen treat options, including shakes, smoothies, and slushes. With its user-friendly controls, operators can easily adjust the consistency and texture of the frozen product, ensuring each serving meets the desired standards of quality. The machine operates with precision, delivering results that are not only delicious but also consistent, enhancing customer satisfaction.

The technology behind the Taylor Model 430 is state-of-the-art, incorporating both advanced refrigeration techniques and easy-to-use electronic controls. Its high-efficiency refrigeration system allows for rapid chilling and freezing, crucial for maintaining the ideal serving temperature for frozen desserts. The unit is equipped with a high-capacity compressor, ensuring that it can handle the demands of a busy service environment while minimizing energy consumption.

Another key characteristic of the Model 430 is its compact design, making it suitable for locations with limited space. Despite its small footprint, the machine does not compromise on capacity, allowing for a substantial output of frozen goods, which is critical in high-demand situations. Additionally, the easy access to internal components simplifies cleaning and maintenance, ensuring that the machine remains in optimal working condition.

The Taylor Model 430 also features an intuitive interface that enables operators to quickly learn and master its functions. This simplicity is paired with robust safety features that protect both the equipment and the user, making it a reliable choice for business owners.

In conclusion, the Taylor Model 430 Torque Shake/Slush Freezer is a standout machine in the market for frozen dessert and beverage production. Its combination of advanced technology, user-friendly design, and versatility makes it an invaluable asset for foodservice establishments looking to expand their offerings while providing high-quality products to their customers. Its reliability and efficiency have made it a trusted choice in the industry, leading to increased profitability and customer satisfaction.
Top Page Image Contents