Taylor model 430 torque shake/slush freezer operating instructions Safety Model 430 Torque

Page 10

This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment’s frame.

SDO NOT allow untrained personnel to operate this machine.

SDO NOT operate the freezer unless all service panels and access doors are restrained with screws.

SDO NOT remove any internal operating parts (examples: freezer door, beater, scraper blades, etc.) unless all control switches are in the OFF position.

Failure to follow these instructions may result in severe personal injury to fingers or hands from hazardous moving parts.

This unit has many sharp edges that can cause severe injuries.

SDO NOT put objects or fingers in the door spout. This may contaminate the product and cause severe personal injury from blade contact.

SUSE EXTREME CAUTION when removing the beater asssembly. The scraper blades are very sharp.

This freezer must be placed on a level surface. Failure to comply may result in personal injury or equipment damage.

Access to the service area of the unit must be restricted to persons having knowledge and practical experience with the unit, in particular as far as safety and hygiene are concerned.

Cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. Please refer to the cleaning section of this manual for the proper procedure to clean this unit.

This machine is designed to maintain product temperature under 41_F (5_C). Any product being added to this machine must be below 41_F (5_C). Failure to follow this instruction may result in health hazards and poor freezer performance.

DO NOT obstruct air intake and discharge openings:

Air cooled units require a minimum of 3” (76.2 mm) of clearance around all sides of the freezer to allow for adequate air flow across condenser. Failure to allow adequate clearance can reduce the refrigeration capacity of the freezer and possibly cause permanent damage to the compressor.

For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of 70_ - 75_F (21_ - 24_C). The freezer has successfully performed in high ambient temperatures of 104_(40_C) at reduced capacities.

DO NOT run the unit without product. Failure to follow this instruction can result in damage to the unit.

NOISE LEVEL: Airborne noise emission does not exceed 78 dB(A) when measured at a distance of 1.0 meter from the surface of the machine and at a height of 1.6 meters from the floor.

130930

 

 

Safety

6

Model 430 Torque

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operators Manual Information found on data plate Table of Contents Table of Contents Section Installer SafetyModel 430 Torque To the Installer Site PreparationElectrical Connections To the Installer Model 430 TorqueAir Cooled Units 130930Refrigerant Beater Rotation130816 To the Operator 131202 To the Operator Model 430 TorqueSection Safety Model 430 Torque Safety130930 Safety Model 430 Torque 070104 Operator Parts IdentificationDescription Part Number Model 430 Torque Operator Parts Identification130816 Operator Parts Identification Model 430 Torque 140102 Section Important To the Operator Model 430 Torque Operating Procedures Section Operating ProceduresAssembly StepOperating Procedures Model 430 Torque Step 090114 Operating Procedures Model 430 Torque SanitizingPriming 140804Draining Product From The Freezing Cylinder Closing Procedure140804 Operating Procedures Model 430 Torque RinsingBrush Cleaning CleaningDisassembly 090114 Model 430 Torque Operating ProceduresRegular Maintenance Checks Important Operator ChecklistDuring Cleaning and Sanitizing 071205 Important Operator Checklist Model 430 TorqueModel 430 Torque Important Operator Checklist Winter StorageSection Troubleshooting Guide Troubleshooting Guide Model 430 TorqueModel 430 Torque Troubleshooting Guide Parts Replacement Schedule Parts Replacement Schedule Model 430 TorqueFrozen Yogurt Product Part Limited Warranty Period Soft ServeModel 430 Torque Limited Warranty on Equipment ShakesLimited Warranty on Equipment Model 430 Torque Part’s Warranty Class Code or Part Limited Warranty Period Model 430 Torque Limited Warranty on PartsLimited Warranty on Parts Model 430 Torque Taylor Company Torque Company 430Torque

model 430 torque shake/slush freezer specifications

The Taylor Model 430 Torque Shake/Slush Freezer is a versatile machine that stands out in the world of foodservice equipment, particularly in the realm of frozen desserts and beverages. This innovative machine is designed to offer high-quality slush and shake production, making it an essential addition to restaurants, cafes, and mobile vending operations.

One of the main features of the Taylor Model 430 is its ability to produce a variety of frozen treat options, including shakes, smoothies, and slushes. With its user-friendly controls, operators can easily adjust the consistency and texture of the frozen product, ensuring each serving meets the desired standards of quality. The machine operates with precision, delivering results that are not only delicious but also consistent, enhancing customer satisfaction.

The technology behind the Taylor Model 430 is state-of-the-art, incorporating both advanced refrigeration techniques and easy-to-use electronic controls. Its high-efficiency refrigeration system allows for rapid chilling and freezing, crucial for maintaining the ideal serving temperature for frozen desserts. The unit is equipped with a high-capacity compressor, ensuring that it can handle the demands of a busy service environment while minimizing energy consumption.

Another key characteristic of the Model 430 is its compact design, making it suitable for locations with limited space. Despite its small footprint, the machine does not compromise on capacity, allowing for a substantial output of frozen goods, which is critical in high-demand situations. Additionally, the easy access to internal components simplifies cleaning and maintenance, ensuring that the machine remains in optimal working condition.

The Taylor Model 430 also features an intuitive interface that enables operators to quickly learn and master its functions. This simplicity is paired with robust safety features that protect both the equipment and the user, making it a reliable choice for business owners.

In conclusion, the Taylor Model 430 Torque Shake/Slush Freezer is a standout machine in the market for frozen dessert and beverage production. Its combination of advanced technology, user-friendly design, and versatility makes it an invaluable asset for foodservice establishments looking to expand their offerings while providing high-quality products to their customers. Its reliability and efficiency have made it a trusted choice in the industry, leading to increased profitability and customer satisfaction.
Top Page Image Contents