Taylor Explore the 430 Manual for Operators and Maintenance
Page 8

Section 2

To the Operator

 

 

The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Model 430 Torque, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, they will require cleaning and maintenance. A minimum amount of care and attention is necessary if the operating procedures outlined in this manual are followed closely.

This Operator’s Manual should be read before operating or performing any maintenance on your equipment.

Your Taylor freezer will NOT eventually compensate for and correct any errors during the set- up or filling operations. Thus, the initial assembly and priming procedures are of extreme importance. It is strongly recommended that personnel responsible for the equipment’s operation, both assembly and disassembly, sit down together and go through these procedures in order to be properly trained and to make sure that no misunderstandings exist.

In the event you should require technical assistance, please contact your local authorized Taylor Distributor.

Note: Your Taylor warranty is valid only if the parts are authorized Taylor parts, purchased from the local authorized Taylor Distributor, and only if all required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on units or parts if non- Taylor approved parts or incorrect refrigerant were installed in the unit, system modifications were performed beyond factory recommendations, or it is determined that the failure was caused by abuse, misuse, neglect, or failure to follow all operating instructions. For full details of your Taylor Warranty, please see the Limited Warranty section in this manual.

Note: Constant research results in steady improvements; therefore, information in this manual is subject to change without notice.

If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is completed, and cannot be disposed as unsorted municipal waste.

The user is responsible for returning the product to the appropriate collection facility, as specified by your local code. For additional information regarding applicable local laws, please contact the municipal facility and/or local distributor.

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this unit are warranted for the term stated in the Limited Warranty section in this manual. However, due to the Montreal Protocol and the U.S. Clean Air Act Amendments of 1990, many new refrigerants are being tested and developed, thus seeking their way into the service industry. Some of these new refrigerants are being advertised as drop- in replacements for numerous applications. It should be noted that in the event of ordinary service to this unit’s refrigeration system, only the refrigerant specified on the affixed data label should be used. The unauthorized use of alternate refrigerants will void your Taylor compressor warranty. It is the unit owner’s responsibility to make this fact known to any technician he employs.

It should also be noted that Taylor does not warrant the refrigerant used in its equipment. For example, if the refrigerant is lost during the course of ordinary service to this unit, Taylor has no obligation to either supply or provide replacement refrigerant either at billable or unbillable terms. Taylor will recommend a suitable replacement if the original refrigerant is banned, obsoleted, or no longer available during the five (5) year Taylor warranty of the compressor.

From time- to- time Taylor may test new refrigerant alternates. Should a new refrigerant alternate prove, through Taylor’s testing, that it would be accepted as a drop- in replacement for this unit, then the disclaimer in this “Compressor Warranty Disclaimer” section will not apply to the use of the alternate refrigerant approved by Taylor.

To find out the current status of an alternate refrigerant as it relates to your compressor warranty, call Taylor or your local authorized Taylor distributor. Be prepared to provide the Model/Serial Number of the unit in question.

Note: Continuing research results in steady improvements; therefore, information in this Operator Manual is subject to change without notice.

131202

 

 

To the Operator

4

Model 430 Torque

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operators Manual Information found on data plate Table of Contents Table of Contents Installer Safety Model 430 Torque To the InstallerSection Site PreparationTo the Installer Model 430 Torque Air Cooled UnitsElectrical Connections 130930130816 Beater RotationRefrigerant To the Operator 131202 To the Operator Model 430 TorqueSection Safety Model 430 Torque Safety130930 Safety Model 430 Torque Operator Parts Identification Description Part Number070104 Model 430 Torque Operator Parts Identification130816 Operator Parts Identification Model 430 Torque 140102 Section Important To the Operator Section Operating Procedures AssemblyModel 430 Torque Operating Procedures StepOperating Procedures Model 430 Torque Step 090114 Operating Procedures Model 430 Torque SanitizingPriming 140804Closing Procedure 140804 Operating Procedures Model 430 TorqueDraining Product From The Freezing Cylinder RinsingCleaning DisassemblyBrush Cleaning 090114 Model 430 Torque Operating ProceduresImportant Operator Checklist During Cleaning and SanitizingRegular Maintenance Checks 071205 Important Operator Checklist Model 430 TorqueModel 430 Torque Important Operator Checklist Winter StorageSection Troubleshooting Guide Troubleshooting Guide Model 430 TorqueModel 430 Torque Troubleshooting Guide Parts Replacement Schedule Parts Replacement Schedule Model 430 TorqueProduct Part Limited Warranty Period Soft Serve Model 430 Torque Limited Warranty on EquipmentFrozen Yogurt ShakesLimited Warranty on Equipment Model 430 Torque Part’s Warranty Class Code or Part Limited Warranty Period Model 430 Torque Limited Warranty on PartsLimited Warranty on Parts Model 430 Torque Taylor Company Torque Company 430Torque

model 430 torque shake/slush freezer specifications

The Taylor Model 430 Torque Shake/Slush Freezer is a versatile machine that stands out in the world of foodservice equipment, particularly in the realm of frozen desserts and beverages. This innovative machine is designed to offer high-quality slush and shake production, making it an essential addition to restaurants, cafes, and mobile vending operations.

One of the main features of the Taylor Model 430 is its ability to produce a variety of frozen treat options, including shakes, smoothies, and slushes. With its user-friendly controls, operators can easily adjust the consistency and texture of the frozen product, ensuring each serving meets the desired standards of quality. The machine operates with precision, delivering results that are not only delicious but also consistent, enhancing customer satisfaction.

The technology behind the Taylor Model 430 is state-of-the-art, incorporating both advanced refrigeration techniques and easy-to-use electronic controls. Its high-efficiency refrigeration system allows for rapid chilling and freezing, crucial for maintaining the ideal serving temperature for frozen desserts. The unit is equipped with a high-capacity compressor, ensuring that it can handle the demands of a busy service environment while minimizing energy consumption.

Another key characteristic of the Model 430 is its compact design, making it suitable for locations with limited space. Despite its small footprint, the machine does not compromise on capacity, allowing for a substantial output of frozen goods, which is critical in high-demand situations. Additionally, the easy access to internal components simplifies cleaning and maintenance, ensuring that the machine remains in optimal working condition.

The Taylor Model 430 also features an intuitive interface that enables operators to quickly learn and master its functions. This simplicity is paired with robust safety features that protect both the equipment and the user, making it a reliable choice for business owners.

In conclusion, the Taylor Model 430 Torque Shake/Slush Freezer is a standout machine in the market for frozen dessert and beverage production. Its combination of advanced technology, user-friendly design, and versatility makes it an invaluable asset for foodservice establishments looking to expand their offerings while providing high-quality products to their customers. Its reliability and efficiency have made it a trusted choice in the industry, leading to increased profitability and customer satisfaction.
Top Page Image Contents