DCS BGB48-BQR, BGB48-BQAR manual Gas Hook-Up

Page 14
*Installation must conform with local codes or with the National Fuel Gas Code ANSI Z223.1 or the CAN/CGA-B149.2 Propane Installation Code
FIG. 08 Natural Gas

INSTALLATION

GAS HOOK-UP

GAS REQUIREMENTS

Verify the type of gas supply to be used, either natural or LP, and make sure the marking on the appliance rating plate agrees with that of the supply. The rating plate is located underneath the unit bottom. Never connect an unregulated gas line to the appliance. You must use the gas regulator provided with the unit, even if the supply is controlled.

An installer-supplied gas shut-off valve must be installed in an easily accessible location. All installer supplied parts must conform to local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1, and the National Fuel Gas Code, ANSI Z223.1 or CAN/CGA-B149.1 Natural Gas Installation Code or CAN/CGA-B149.2 Propane Installation Code.

All pipe sealants must be an approved type and resistant to the actions of LP gases. Never use pipe sealant on flare fittings. All gas connections should be made by a qualified technician and in accordance with local codes and ordinances. In the absence of local codes, the installation must comply with the National Fuel Gas Code ANSI Z223.1. Gas conversion kits are available from the factory. When ordering gas conversion kits, have the model number, and the type of gas (natural or LP) from your grill.

TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:

BGB48-BQR - 126,500 Btu/hr

BGB48-BQAR - 121,500 Btu/hr BGB36-BQAR - 92,500 Btu/hr

The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The instal- lation of this appliance must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. Installation in Canada must be in accordance with the Standard Can1-b149.1 and/or .2 (installation code for gas burning appliances and

equipment) and local codes.

NATURAL GAS HOOK UP: (THIS TYPE OF CON-

 

 

NECTION SHOULD BE PERFORMED BY A CERTIFIED OR

 

 

LICENSED TECHNICIAN ONLY.)

Bottom of unit

 

Connection: 1/2" NPT male with 3/8" flare adapter.

 

 

Operating pressure: 4.0" W.C. Supply pressure: 5" to 14"

Threading compound

Coupling

water column. If in excess of 14" W.C., a step down

1/2 NPT

must be resistant to LP gas

regulator is required. Check with your local gas utility

 

Close

 

NIpple

company or local codes for instructions on installing gas

 

 

Regulator

supply lines. Be sure to check on type and size of run,

1/2 x 5" NPT

4.0" W.C.

 

 

and how deep to bury the line. If the gas line is too small,

Close

 

the grill will not function properly. Any joint sealant used

Nipple

Adapter 1/2 NPT

 

 

to 3/8 flare fitting

must be an approved type and be resistive to the actions

Installer supplied shut-off

 

of LP gases.

valve must be easily

Do not put threading

accessible*

 

 

compound on these

 

 

threads

TO HOOK-UP THE FITTINGS SUPPLIED WITH

THE GRILL:

Assemble as shown (Fig. 08). Use threading compound on male threads only. Do not use threading compound on the male end of the 1/2 NPT to 3/8 flare adapter. Use a second pipe wrench to hold the grill inlet pipe to avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points in the direction of gas flow towards

the unit, away from the supply. Do not forget to place the installer-supplied gas valve in an accessible location.

LP GAS HOOK UP (TYPE 1 OR QCC1 REGULATOR):

Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assembly for connection to a standard 20 lb. LP cylinder (Type 1). The LP tank is not included.

12

Image 14
Contents Professional 36/48 BGB Grill Page Message to OUR Customers Please Retain this Manual for Future ReferenceTable of Contents Safety Practices & Precautions Important Safety NoticeGrill Placement Preferred AIR FlowSafety Practices & Precautions Grill Models Location InstallationLocating GRILL/BUILT-IN Clearances Clearances to Non-Combustible Construction Clearances to Non-Combustible ConstructionInsulated Jacket Clearances to Combustible ConstructionGeneral BUILT-IN Construction Details Access Drawers Cutout dimensions GAS HOOK-UP LP Tank Requirements LP GasLP Tank Restraint for BUILT-IN Installation 18 maxStep To Test Leak TestingBefore Testing LOW Flame Setting Adjustment Burner AdjustmentGrill Burner AIR Adjustment Grill Burner Flame HeightRadiant Assembly Radiant Asssembly InstallationInstaller Checklist These InstructionsTo Light the Grill Burner Using the GrillLighting Instructions Burner GrillingDIRECT/INDIRECT Cooking Notes Burner OffShaped Grate Radius Grate Grilling HintsDUAL-SIDED Grates Wood Chips Using the Smoker SystemTo Light the Smoker Burner Using the Rotisserie ROD LightWorking Area PreparationRecommended Meat PreparationTo Light the Rotisserie Burner Before Cooking Manual LightingCooking on Rotisserie Care and Maintenance Orifice Cleaning To Remove the U-BURNERS for CleaningGrill Burner Cleaning Stainless SteelSide Burners BGB48 BQR Model Smoker BurnerGrill WON’T Light When the Ignition Button is Pushed TroubleshootingBefore Calling for Service LOW Heat with Knob in HI/SEAR PositionService HOW to Obtain ServiceHOW Long does this Limited Warranty LAST? WarrantyLimited Warranty This Warranty does not CoverNo Other Warranties HOW to GET ServiceCommercial USE LE Gril DE Série Professionnelle BGB 36/48 PO Lintention DE NOS Clients Veuillez Conserver CE Manuel À Titre DE RéférenceTable DES Matières Mesures DE Sécurité ET DE Précaution AutocollantDe ventilation Emplacement DU Gril Flux Dévent DE SortieRemarque Modèles DE Gril Emplacement DU Gril ET DES Dégagements EmplacementEspaces de dégagement pour une construction non combustible Généralités Enveloppe IsoléeDétails Dune Construction Intégrée Disposition standard pour une enceinte non combustible+0,-1/8 +1/8,-0 Branchement DU GAZ Naturel Branchement DU GAZExigences Concernant LE GAZ Pour Connecter LES Raccords Fournis Avec LE GrilMise EN Garde Exigences Concernant LA Bouteille DE PropaneRemarque Placez le dispositif de retenue de bouteille dans lîlot Fig Pour tester Test DE Détection DES FuitesAvant la vérification Hauteur DES Flammes DU Brûleur DU Gril Réglages DES BrûleursRéglage Dair DU Brûleur DU Gril Réglages Pour Niveau BASInstallation DE Lensemble DU Radiant Installation DE Lensemble DU RadiantListe DE Contrôle DE Linstallateur Pour Allumer LE Brûleur DU Gril Utilisation DU GrilInstructions Dallumage Allumage du gril à lallumetteBrûleurs latéraux Instructions DALLUMAGE/CUISSON SUR GrilAllumage des brûleurs latéraux avec une allumette GrilCuisson SUR Gril Conseils AU Sujet DU GrilGrilles Double Face Grille EN Forme DE « W » Grille ArondieCopeaux DE Bois Utilisation DU Système À FumoirPour Allumer LE Brûleur À Fumoir Utilisation DE LA Rôtissoire Recommandé PréparationPour Allumer LE Brûleur DE Rôtisserie Avant DE Faire Cuire Allumage ManuelCuisson SUR LA Rôtissoire Entretien ET Nettoyage Brûleur DU Gril Acier InoxydableÉlectrodes Déposer DES Brûleurs EN U Pour LE NettoyageBrûleurs Latéraux BGB48 BQR Modele Brûleur À FumoirLE Gril NE Sallume PAS Lorsquon Enfonce LE Bouton Dallumage Avant Dappeler LE Service TechniqueDépannage Chaleur Faible Avec LE Bouton EN Position « SEAR/HI »Pour Lobtention DU Service DE Garantie Fisher & Paykel Sengage À GarantieGarantie Limitée Quelle EST LA Durée DE Cette Garantie LIMITÉE?Aucune Autre Garantie Pour Obtenir DES RéparationsUtilisation Commerciale Remarque Page Litho in USA 09/2001

BGB48-BQAR, BGB48-BQR specifications

The DCS BGB48-BQR and BGB48-BQAR are cutting-edge battery systems designed for a range of applications, primarily focusing on delivering reliable energy storage solutions. These models are part of a contemporary line of products that exemplify advanced technologies in battery management and energy efficiency.

One of the key features of the BGB48-BQR and BGB48-BQAR is their high energy density, which maximizes the usable energy within a compact form factor. This is particularly beneficial for applications that require a substantial amount of energy but have limited space for battery installation. The sleek design not only enhances the aesthetics of installations but also allows for flexible integration into existing systems.

The technology utilized in these batteries includes lithium-ion cells, which are renowned for their longevity and performance. With a cycle life that often surpasses 3,000 cycles, users can expect these batteries to maintain their capacity over extended periods, reducing the need for frequent replacements. This durability translates into lower operational costs and less environmental impact.

Another standout characteristic is the sophisticated Battery Management System (BMS) integrated into both models. The BMS continuously monitors the health of each battery cell, ensuring optimal performance and safety. It balances charging and discharging processes, mitigates risks of overcharging or overheating, and extends the overall lifespan of the battery. Additionally, the BMS provides real-time data to users, facilitating informed decision-making regarding energy consumption and battery usage.

Safety is a paramount consideration in the design of the DCS BGB48-BQR and BGB48-BQAR systems. These batteries incorporate multiple layers of protection, including thermal management that prevents overheating, as well as protective circuits that safeguard against short circuits and electrical surges.

Furthermore, both models support various communication protocols, enabling seamless integration with smart energy systems. This feature allows them to interact with solar panels, inverters, and grid systems, making them suitable for renewable energy applications and storage.

In summary, the DCS BGB48-BQR and BGB48-BQAR represent the forefront of battery technology with their high energy density, advanced BMS, robust safety features, and adaptability for a diverse range of applications. These characteristics make them an ideal choice for businesses and individuals seeking efficient, reliable, and sustainable energy storage solutions.