DCS BGB48-BQR, BGB48-BQAR manual Using the Grill, Lighting Instructions, To Light the Grill Burner

Page 22

USING THE GRILL

LIGHTING INSTRUCTIONS

TO LIGHT THE GRILL BURNER:

Open the grill lid and/or remove the top grate cover from side burner (for 48BQR) before lighting. Turn all knobs to “OFF”. Turn the main gas supply on slowly. If you smell gas, shut off gas supply and call for service.

Push and hold the ignition button, turn the selected burner knob to “SEAR”. If burner does not light in 4 to 5 seconds, turn knob “OFF” and wait 5 minutes before trying again for any accumulated gas to dissipate.

Grill Match Lighting:

If the burner will not light after several attempts then the burner can be match lit. If you’ve just attempted to light the burner with the ignition, allow 5 minutes for any accumulated gas to dissipate. Keep your face as far away from the grill as possible and hold and pass a lit, paper book match over the hole located on the top left for burner on the left, or the right hole for the right burner (Fig. 26

&Fig. 27). Push and turn the control knob which is centered on the burner where the lit match is located, to “SEAR/HI”. If the

burner does not light in 4 seconds, turn the knob off, wait 5 minutes and try

FIG. 26

FIG. 27

again.

Once the left or right burner is lit, the adjacent burner can be lit by the cross-lighting method. For center burners to cross light, light the adjacent far left or right burner using the standard or match light procedure. Push and turn the control knob for the desired center burner to “HI”. The gas will be ignited by the adjacent burners flame. If the burner does not light in 4 seconds, turn knob off, wait 5 minutes and try again.

NOTE:

 

 

 

Improper lighting procedures can cause the LP tank flow control to activate,

 

 

WARNING

resulting in reduced heat output. If this is suspected, to reset flow control,

 

 

Failure to follow the steps in the order shown may cause the Flow

shut off all burner controls and LP cylinder valve, wait 30 seconds, then turn

Limiting Device to activate resulting in extremely low gas flow and

LP cylinder valve on extremely slowly, wait five (5) seconds and push and

improper operation.

 

1

OFF

All knobs must be in the OFF position before

hold the ignition button and turn burner valve on to “SEAR”.

 

 

 

opening LP tank valve.

 

 

SEAR

 

 

2

 

Attach regulator hose assembly to tank.

TO LIGHT DUAL SIDE BURNERS (48BQR MODELS ONLY):

3

 

 

CAUTION!

 

Now open the LP tank valve two (2) full

 

 

turns min.

 

 

 

The side burner cover may be hot if the grill burners are in operation.

Side Burners Lighting Instructions:

 

 

First remove the burner cover and any cooking utensils from the burner

 

IGNITION

grate. Push and hold the ignition button, turn the control knob to the “HI”

 

 

position until the burner is lit or 4 seconds pass. If the burner doesn’t ignite,

 

 

wait 5 minutes for any accumulated gas to dissipate then try again. If the

 

 

burner will not light after several attempts, check the trouble shooting

Control Knobs

Ignition

instructions on page 31.

 

 

 

FIG. 28

 

Side Burners Match Lighting:

Hold a lit paper book match near the burner ports, turn the control knob counterclockwise to “HI”. Move your hand immediately once the burner is lit. Rotate the control knob to the desired setting.

Note:

If you are using propane gas, a slight pop or flash may occur at the burner ports a few seconds after the burner has been turned “off”. This “extinction pop” is normal for propane gas.

Cap

FIG. 29

Side burners:

Your side burner is equipped with burners typical of those used in restaurants. These burners are designed for maximum cleanability and controlability. The burner should never be operated if the cap is not in place (Fig. 29).

20

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Professional 36/48 BGB Grill Page Message to OUR Customers Please Retain this Manual for Future ReferenceTable of Contents Safety Practices & Precautions Important Safety NoticeGrill Placement Preferred AIR FlowSafety Practices & Precautions Grill Models Locating GRILL/BUILT-IN Clearances InstallationLocation Clearances to Non-Combustible Construction Clearances to Non-Combustible ConstructionGeneral Clearances to Combustible ConstructionInsulated Jacket BUILT-IN Construction Details Access Drawers Cutout dimensions GAS HOOK-UP LP Tank Requirements LP GasLP Tank Restraint for BUILT-IN Installation 18 maxStep Before Testing Leak TestingTo Test LOW Flame Setting Adjustment Burner AdjustmentGrill Burner AIR Adjustment Grill Burner Flame HeightRadiant Assembly Radiant Asssembly InstallationInstaller Checklist These InstructionsLighting Instructions Using the GrillTo Light the Grill Burner Burner GrillingDIRECT/INDIRECT Cooking Notes Burner OffDUAL-SIDED Grates Grilling HintsShaped Grate Radius Grate To Light the Smoker Burner Using the Smoker SystemWood Chips Using the Rotisserie ROD LightWorking Area PreparationRecommended Meat PreparationTo Light the Rotisserie Burner Before Cooking Manual LightingCooking on Rotisserie Care and Maintenance Orifice Cleaning To Remove the U-BURNERS for CleaningGrill Burner Cleaning Stainless SteelSide Burners BGB48 BQR Model Smoker BurnerGrill WON’T Light When the Ignition Button is Pushed TroubleshootingBefore Calling for Service LOW Heat with Knob in HI/SEAR PositionService HOW to Obtain ServiceHOW Long does this Limited Warranty LAST? WarrantyLimited Warranty This Warranty does not CoverCommercial USE HOW to GET ServiceNo Other Warranties LE Gril DE Série Professionnelle BGB 36/48 PO Lintention DE NOS Clients Veuillez Conserver CE Manuel À Titre DE RéférenceTable DES Matières Mesures DE Sécurité ET DE Précaution AutocollantDe ventilation Emplacement DU Gril Flux Dévent DE SortieRemarque Modèles DE Gril Emplacement DU Gril ET DES Dégagements EmplacementEspaces de dégagement pour une construction non combustible Généralités Enveloppe IsoléeDétails Dune Construction Intégrée Disposition standard pour une enceinte non combustible+0,-1/8 +1/8,-0 Branchement DU GAZ Naturel Branchement DU GAZExigences Concernant LE GAZ Pour Connecter LES Raccords Fournis Avec LE GrilMise EN Garde Exigences Concernant LA Bouteille DE PropaneRemarque Placez le dispositif de retenue de bouteille dans lîlot Fig Avant la vérification Test DE Détection DES FuitesPour tester Hauteur DES Flammes DU Brûleur DU Gril Réglages DES BrûleursRéglage Dair DU Brûleur DU Gril Réglages Pour Niveau BASInstallation DE Lensemble DU Radiant Installation DE Lensemble DU RadiantListe DE Contrôle DE Linstallateur Pour Allumer LE Brûleur DU Gril Utilisation DU GrilInstructions Dallumage Allumage du gril à lallumetteBrûleurs latéraux Instructions DALLUMAGE/CUISSON SUR GrilAllumage des brûleurs latéraux avec une allumette GrilCuisson SUR Gril Conseils AU Sujet DU GrilGrilles Double Face Grille EN Forme DE « W » Grille ArondiePour Allumer LE Brûleur À Fumoir Utilisation DU Système À FumoirCopeaux DE Bois Utilisation DE LA Rôtissoire Recommandé PréparationPour Allumer LE Brûleur DE Rôtisserie Avant DE Faire Cuire Allumage ManuelCuisson SUR LA Rôtissoire Entretien ET Nettoyage Brûleur DU Gril Acier InoxydableÉlectrodes Déposer DES Brûleurs EN U Pour LE NettoyageBrûleurs Latéraux BGB48 BQR Modele Brûleur À FumoirLE Gril NE Sallume PAS Lorsquon Enfonce LE Bouton Dallumage Avant Dappeler LE Service TechniqueDépannage Chaleur Faible Avec LE Bouton EN Position « SEAR/HI »Pour Lobtention DU Service DE Garantie Fisher & Paykel Sengage À GarantieGarantie Limitée Quelle EST LA Durée DE Cette Garantie LIMITÉE?Utilisation Commerciale Pour Obtenir DES RéparationsAucune Autre Garantie Remarque Page Litho in USA 09/2001

BGB48-BQAR, BGB48-BQR specifications

The DCS BGB48-BQR and BGB48-BQAR are cutting-edge battery systems designed for a range of applications, primarily focusing on delivering reliable energy storage solutions. These models are part of a contemporary line of products that exemplify advanced technologies in battery management and energy efficiency.

One of the key features of the BGB48-BQR and BGB48-BQAR is their high energy density, which maximizes the usable energy within a compact form factor. This is particularly beneficial for applications that require a substantial amount of energy but have limited space for battery installation. The sleek design not only enhances the aesthetics of installations but also allows for flexible integration into existing systems.

The technology utilized in these batteries includes lithium-ion cells, which are renowned for their longevity and performance. With a cycle life that often surpasses 3,000 cycles, users can expect these batteries to maintain their capacity over extended periods, reducing the need for frequent replacements. This durability translates into lower operational costs and less environmental impact.

Another standout characteristic is the sophisticated Battery Management System (BMS) integrated into both models. The BMS continuously monitors the health of each battery cell, ensuring optimal performance and safety. It balances charging and discharging processes, mitigates risks of overcharging or overheating, and extends the overall lifespan of the battery. Additionally, the BMS provides real-time data to users, facilitating informed decision-making regarding energy consumption and battery usage.

Safety is a paramount consideration in the design of the DCS BGB48-BQR and BGB48-BQAR systems. These batteries incorporate multiple layers of protection, including thermal management that prevents overheating, as well as protective circuits that safeguard against short circuits and electrical surges.

Furthermore, both models support various communication protocols, enabling seamless integration with smart energy systems. This feature allows them to interact with solar panels, inverters, and grid systems, making them suitable for renewable energy applications and storage.

In summary, the DCS BGB48-BQR and BGB48-BQAR represent the forefront of battery technology with their high energy density, advanced BMS, robust safety features, and adaptability for a diverse range of applications. These characteristics make them an ideal choice for businesses and individuals seeking efficient, reliable, and sustainable energy storage solutions.
Top Page Image Contents