DCS BGB48-BQR, BGB48-BQAR manual Care and Maintenance

Page 30

 

CARE AND MAINTENANCE

 

 

 

BATTERY REPLACEMENT:

 

 

1.

Remove drip pan.

 

 

2.

Open cart door (on cart model only).

 

 

3.

Pull battery downwards (This may require use of pliers).

 

 

4.

Re-install upward and push to snap - Fig. 43. (Polarity is

 

 

 

shown in Fig. 44).

 

 

 

Note:

FIG. 43

FIG. 44

 

Battery condition should be checked at least once a year.

 

 

 

REGULATOR AND HOSE REPLACEMENT

The pressure regulator and hose assembly supplied with the unit must be used. If replacements are needed, contact Customer Care (888) 281-5698. Do not use the grill if the odor of gas is present. If the unit is LP, screw the regulator into the tank and leak check the hose and regulator connections with a soap and water solution before operating the grill. Turn all knobs to "OFF" then turn on the gas supply. If LP, is there gas in the tank?

■Always keep your face and body as far away from the grill as possible when lighting.

■DO NOT leave the grill unattended while cooking.

■Keep a spray bottle of soapy water near the gas supply valve and check the connections before each use.

■Do not attempt to "LITE" the grill if the odor of gas is present.

■Wait 5 minutes before relighting a hot grill.

GRILL GRATES:

Method 1: Turn on “HI” for 15-20 minutes to burn any remaining food particles. After turning the grill “OFF”, use a bristle barbeque brush to remove any remainin food particles or ash.

Method 2: The easiest way to clean the grill is immediately after cooking is completed and after turning off the flame. Wear a barbeque mitt to protect your hand from the heat and steam. Dip a soft brass bristle barbeque brush in a mixture of 2 cups of tap water and 1/2 cup of vinegar and scrub the hot grill. Dip the brush frequently in the bowl of water and vinegar. Steam, created as water contacts the hot grill, assists the cleaning process by softening any food particles. The food particles will fall onto the ceramic rods and burn or fall into the drip pan. If the grill is allowed to cool before cleaning, cleaning will be more difficult.

Method 3: Take about 1 foot of aluminum foil, crumbled up in a ball and rubbing it over cooled grates to release food particles.

Note:

Grill grates must be re-seasoned after cleaning to prevent rust stains.

DRIP PAN AND GREASE TRAY:

The full width drip pan with grease tray will collect grease from the grill section and boil overs and spills from the side burners. Allow the pan and its contents to cool before attempting to clean. Clean grease from the pan often to avoid the possibility of a grease fire.

CERAMIC RODS:

It is not necessary to remove the ceramic rods for cleaning. They burn themselves clean during the next cooking operation. Periodically the trays holding the ceramic rods need to be turned over, and shaken free of debris for a thorough cleaning. How often you use the grill and the amount and type of food cooked will determine when it is necessary to clean the trays. If grease can be seen on the top of the tubes or if you get a lot of flare-up during cooking, the tubes need to be turned over and heated on “HI” for 30 minutes; longer for heavy soil.

28

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Professional 36/48 BGB Grill Page Message to OUR Customers Please Retain this Manual for Future ReferenceTable of Contents Safety Practices & Precautions Important Safety NoticeGrill Placement Preferred AIR FlowSafety Practices & Precautions Grill Models Installation Locating GRILL/BUILT-IN ClearancesLocation Clearances to Non-Combustible Construction Clearances to Non-Combustible ConstructionClearances to Combustible Construction GeneralInsulated Jacket BUILT-IN Construction Details Access Drawers Cutout dimensions GAS HOOK-UP LP Tank Requirements LP GasLP Tank Restraint for BUILT-IN Installation 18 maxStep Leak Testing Before TestingTo Test LOW Flame Setting Adjustment Burner AdjustmentGrill Burner AIR Adjustment Grill Burner Flame HeightRadiant Assembly Radiant Asssembly InstallationInstaller Checklist These InstructionsUsing the Grill Lighting InstructionsTo Light the Grill Burner Burner GrillingDIRECT/INDIRECT Cooking Notes Burner OffGrilling Hints DUAL-SIDED GratesShaped Grate Radius Grate Using the Smoker System To Light the Smoker BurnerWood Chips Using the Rotisserie ROD LightWorking Area PreparationRecommended Meat PreparationTo Light the Rotisserie Burner Before Cooking Manual LightingCooking on Rotisserie Care and Maintenance Orifice Cleaning To Remove the U-BURNERS for CleaningGrill Burner Cleaning Stainless SteelSide Burners BGB48 BQR Model Smoker BurnerGrill WON’T Light When the Ignition Button is Pushed TroubleshootingBefore Calling for Service LOW Heat with Knob in HI/SEAR PositionService HOW to Obtain ServiceHOW Long does this Limited Warranty LAST? WarrantyLimited Warranty This Warranty does not CoverHOW to GET Service Commercial USENo Other Warranties LE Gril DE Série Professionnelle BGB 36/48 PO Lintention DE NOS Clients Veuillez Conserver CE Manuel À Titre DE RéférenceTable DES Matières Mesures DE Sécurité ET DE Précaution AutocollantDe ventilation Emplacement DU Gril Flux Dévent DE SortieRemarque Modèles DE Gril Emplacement DU Gril ET DES Dégagements EmplacementEspaces de dégagement pour une construction non combustible Généralités Enveloppe IsoléeDétails Dune Construction Intégrée Disposition standard pour une enceinte non combustible+0,-1/8 +1/8,-0 Branchement DU GAZ Naturel Branchement DU GAZExigences Concernant LE GAZ Pour Connecter LES Raccords Fournis Avec LE GrilMise EN Garde Exigences Concernant LA Bouteille DE PropaneRemarque Placez le dispositif de retenue de bouteille dans lîlot Fig Test DE Détection DES Fuites Avant la vérificationPour tester Hauteur DES Flammes DU Brûleur DU Gril Réglages DES BrûleursRéglage Dair DU Brûleur DU Gril Réglages Pour Niveau BASInstallation DE Lensemble DU Radiant Installation DE Lensemble DU RadiantListe DE Contrôle DE Linstallateur Pour Allumer LE Brûleur DU Gril Utilisation DU GrilInstructions Dallumage Allumage du gril à lallumetteBrûleurs latéraux Instructions DALLUMAGE/CUISSON SUR GrilAllumage des brûleurs latéraux avec une allumette GrilCuisson SUR Gril Conseils AU Sujet DU GrilGrilles Double Face Grille EN Forme DE « W » Grille ArondieUtilisation DU Système À Fumoir Pour Allumer LE Brûleur À FumoirCopeaux DE Bois Utilisation DE LA Rôtissoire Recommandé PréparationPour Allumer LE Brûleur DE Rôtisserie Avant DE Faire Cuire Allumage ManuelCuisson SUR LA Rôtissoire Entretien ET Nettoyage Brûleur DU Gril Acier InoxydableÉlectrodes Déposer DES Brûleurs EN U Pour LE NettoyageBrûleurs Latéraux BGB48 BQR Modele Brûleur À FumoirLE Gril NE Sallume PAS Lorsquon Enfonce LE Bouton Dallumage Avant Dappeler LE Service TechniqueDépannage Chaleur Faible Avec LE Bouton EN Position « SEAR/HI »Pour Lobtention DU Service DE Garantie Fisher & Paykel Sengage À GarantieGarantie Limitée Quelle EST LA Durée DE Cette Garantie LIMITÉE?Pour Obtenir DES Réparations Utilisation CommercialeAucune Autre Garantie Remarque Page Litho in USA 09/2001

BGB48-BQAR, BGB48-BQR specifications

The DCS BGB48-BQR and BGB48-BQAR are cutting-edge battery systems designed for a range of applications, primarily focusing on delivering reliable energy storage solutions. These models are part of a contemporary line of products that exemplify advanced technologies in battery management and energy efficiency.

One of the key features of the BGB48-BQR and BGB48-BQAR is their high energy density, which maximizes the usable energy within a compact form factor. This is particularly beneficial for applications that require a substantial amount of energy but have limited space for battery installation. The sleek design not only enhances the aesthetics of installations but also allows for flexible integration into existing systems.

The technology utilized in these batteries includes lithium-ion cells, which are renowned for their longevity and performance. With a cycle life that often surpasses 3,000 cycles, users can expect these batteries to maintain their capacity over extended periods, reducing the need for frequent replacements. This durability translates into lower operational costs and less environmental impact.

Another standout characteristic is the sophisticated Battery Management System (BMS) integrated into both models. The BMS continuously monitors the health of each battery cell, ensuring optimal performance and safety. It balances charging and discharging processes, mitigates risks of overcharging or overheating, and extends the overall lifespan of the battery. Additionally, the BMS provides real-time data to users, facilitating informed decision-making regarding energy consumption and battery usage.

Safety is a paramount consideration in the design of the DCS BGB48-BQR and BGB48-BQAR systems. These batteries incorporate multiple layers of protection, including thermal management that prevents overheating, as well as protective circuits that safeguard against short circuits and electrical surges.

Furthermore, both models support various communication protocols, enabling seamless integration with smart energy systems. This feature allows them to interact with solar panels, inverters, and grid systems, making them suitable for renewable energy applications and storage.

In summary, the DCS BGB48-BQR and BGB48-BQAR represent the forefront of battery technology with their high energy density, advanced BMS, robust safety features, and adaptability for a diverse range of applications. These characteristics make them an ideal choice for businesses and individuals seeking efficient, reliable, and sustainable energy storage solutions.
Top Page Image Contents